background image

 

 

 

 

Figure 19. Coolant Pump mounted on top 
of tank. 

 

Locate, remove and discard the two screws on the side of 

the spindle head as shown in Figure 17. New bolts are 

supplied with the coolant tank assembly

. Note these 

screws may be painted heavy and hard to see!! 

 

 

 

 

 

 

Connect the Plastic Coolant Tube(6) to the Connecting 

Tube (4); Place the Connecting Tube (4) into the 

Support (5); Fasten the Nut on the Flexible Tube (1) to 

the Connecting Tube (4); Use the Cap Screws (8) to fix 

the Support (5) to the Mill Head (9). Finally tighten the 

Screw (7) to fix the Connecting Tube (4). The completed 

assembly is shown Figure 18.

 

 

 

 

The coolant pump is mounted on the top of the coolant tank as 

shown in 19. Use Teflon tape on the connection. Note that the 

coolant pump is dual voltage (110VAC/220VAC). The pump is 

shipped with the wiring configured for 110 VAC. If the pump is to be 

used with 220 VAC unscrew the electrical pump cover plate and 

re-wire the pump per the diagram on the inside of the lid. 

 

Figure 18. Coolant tube to mill connections.   

 

Figure 17. shows 2 plug screws on side of 
spindle, screws must be removed and 
discarded. 

 

Содержание PCNC 770














Отзывы: