background image

5. 4.   Leak from pump ( leak from other than gland ) 

Possible Cause 

Remedy / Corrective Action 

 

1. Insufficient tightening torque of mounting 

bolts.  

 

Retighten them with uniform tightening torque after complete 

shutdown internal pressure drop and complete cool-down of the 

pump.  

 

2.  O-rings. 

 

Retighten the bolts.If fluid still leaks even after retightened, replace 

O-ring with new one. 

 

3.  Rapid change of fluid temperature. 

 

Rapid temperature down would cause eventual leak from the pump. 

Accordingly, check whether or not fluid leaks from the pump even 

after the temperature rises up to normal degree. If still  leaked, it will 

show fault of O-ring. When fluid still leaks even after the bolts 

retightened, take corrective action in the above item-2.   

   

 

 

5. 5.   Leak from gland packing 

Possible Cause 

Remedy / Corrective Action 

 

1.  Wear or imperfection or improper insertion 

of packing rings. 

 

Re-insert the packing rings. 

 

2.  Damage of packing sleeve caused by over-

clamped or irregularly clamped gland. 

 

Re-polish or replace the sleeve. After replacement of the packing, 

tighten carefully the gland nut. 

 

3.  Unsmooth rotation of pump, so called, 

swing of the shaft. 

 

Unsmooth rotation of the shaft cause leak from the gland. In such 

event, check carefully gap in the bearing and replace it with new one 

if necessary. If fluid still leak even after replacement, overhaul the 

pump to find out faulty part. 

 

 

 

5. 6.   Overheat of bearing 

Possible Cause 

Remedy / Corrective Action 

 

1. Imperfect centering of pump and driver 

(motor). 

 

Check the centering and leveling state. 

 

2.   Abnormal piping load acts on the pump. 

 

Modify properly the piping to remove abnormal load on the pump, 

and make re-centering. 

 

3. Inaccurate clearance between coupling 

 

halves. 

 

Adjust it to the value shown in the drawing. 

 

4. Damage of bearing or deterioration of 

grease. 

 

Replace the bearing or grease with new one. 

Содержание MMO

















Отзывы: