TORCHVIEW CDVR-0402U Скачать руководство пользователя

Страница: 31 / 41

- 31 -

4.3. Recording

The initial recording configuration for this DVR is set up as follows :

CATEGORY

DEFAULT VALUE

RECORDING SPEED
- NTSC
- PAL

15FPS(Frames Per Second)
12FPS(Frames Per Second)

RECORDING QUALITY

MIDDLE

RESOLUTION

- NTSC

- PAL

352x240(CIF)
352x288(CIF)

RECORDING SCHEDULE

CONTINUOUS

AUDIO RECORDING

ALL

FULL DISK

OVERWRITE

WATERMARK NO

※

To change the above configurations, enter SETUP and change the settings from the RECORD SET and

RECORD SCHEDULE menus.

※

Recording Indicator : The following indicator will appear on the monitoring screen for each channels.

: Recording schedule has been set up.

- Blinking

: Actual recording is in progress.

- Blinking

: Motion detection recording is in progress

- Blinking

: Sensor activated recording in progress.

PANIC RECORDING

Press the PANIC button during an emergency to activate recordings of all cameras at the highest recording

quality level and the OSD “R” will change to “

”.

      RECORDING SPEED : 30FPS/NTSC, 25FPS/PAL
      RECORDING QUALITY : SUPER

※

The resolution will remain in its original recoding setting.

You may de-activate the PANIC recording by pressing the PANIC button once again and the DVR will continue
to operate based on the original recording settings.

Operation

Содержание CDVR-0402U










































Результаты поиска

Содержание CDVR-0402U

Отзывы:

Похожие инструкции для CDVR-0402U

Бренды по названию

Популярные бренды

TORCHVIEW CDVR-0402U, Руководство пользователя

Результаты поиска

Содержание CDVR-0402U

Отзывы:

Похожие инструкции для CDVR-0402U

Бренды по названию

Популярные бренды