manualshive.com logo in svg

Toradex Apalis Series, Руководство по конструкции

Поделиться
Скачать
Toradex Apalis Series Скачать руководство пользователя страница 13

 

 

Apalis Carrier Board Design Guide 

Toradex AG  l  Altsagenstrasse 5  l  6048 Horw  l  Switzerland  l  +41 41 500 48 00  l  

www.toradex.com 

 l  

[email protected] 

Page | 13 

 

Figure 3: Pin numbering schema on the bottom side of the module 

 

 

Figure 4: Pin numbering schema on the module connector land pattern 

 

2.2  PCI Express 

The Apalis module form factor only features one PCIe lane as standard interface. Depending on 
the module, there may be additional lanes available in the type-specific area.  

2.2.1 

PCIe Signals 

Apalis 
Pin 

Apalis 
Signal Name 

I/O 

Type 

Power 
Rail 

Description 

55 

PC 

O 

PCIe 

 

PCIe 100MHz reference clock output positive 

53 

PCIE1_CLK- 

O 

PCIe 

 

PCIe 100MHz reference clock output negative 

49 

P 

O 

PCIe 

 

PCIe transmit data positive 

47 

PCIE1_TX- 

O 

PCIe 

 

PCIe transmit data negative 

43 

P 

I 

PCIe 

 

PCIe receive data positive 

41 

PCIE1_RX- 

I 

PCIe 

 

PCIe receive data negative 

37 

WAKE1_MICO 

I 

CMOS 

3.3V 

General purpose wake signal 

26 

RESET_MOCI# 

O 

CMOS 

3.3V 

General reset output of the module 

209 

I2C1_SDA 

I/O 

OD 

3.3V 

I2C interface data, some PICe device need SMB interface for special 
configuration 

211 

I2C1_SCL 

O 

OD 

3.3V 

I2C interface clock, some PICe device need SMB interface for special 
configuration 

Table 3: PCIe signals 

 
The PCIe interface supports polarity inversion. This means that the positive and negative signal pins 
can be inverted in order to simplify the layout by avoiding crossing of the signals. Some PCIe 
devices support additional lane reversal for multi-lane interfaces. As the standard interfaces on 
Apalis provide only a single lane PCIe interface, the lane reversal feature is not relevant to the 
Apalis specification. Some Apalis modules provide additional multi-lane PCIe interfaces as type-
specific interfaces. Please consult the datasheets of such modules to determine if lane reversal is 

applicable and supported.  
 

Bottom Side

  

Pin1

Pin23

Pin2

Pin24

Pin173

Pin164

Pin174

Pin321

Pin320

Pin165

Pin17

Pin18

Module Insertion Edge

Содержание Apalis Series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды