Topsun HCS128 Скачать руководство пользователя страница 32

Original Instructions

 

 

31 

10. 

Storage 

1. Empty the fuel tank and run the engine out of fuel. 
2. Empty the oil tank. 
3. Clean the entire unit. 
4. Store the unit in a dry place out of the reach of children. 

 

11. 

Waste disposal and environmental protection

 

Never  pour  remainders  of  chain  lubricant  or  2-stroke  fuel  mixture  in  the  drain  or 
sewerage system or soil, but dispose of it in a proper, environmentally friendly way, e.g., 
at a special collecting point or dump. 
If  your  device  should  become  useless  somewhere  in  the  future  or  you  do  not  need  it 
any  longer,  do  not  dispose  of  the  device  together  with  your  domestic  refuse,  but 
dispose of it in an environmentally friendly manner. Thoroughly empty the oil/lubricant 
and  fuel  tanks  and  dispose  of  the  remainders  at  a  special  collecting  point  or  dump. 
Please  also  dispose  of  the  device  itself  at  an  according  collecting/recycling  point.  By 
doing so, plastic and metal parts can be separated and recycled. Information concerning 
the disposal of materials and devices are available from your local administration.

 

 

12.

 Warranty

 

For  this  petrol  tool,  the  company  provides  the  end  user  -  independently  from  the 

retailer‘s  obligations  resulting  from  the  purchasing  contract 

-  with  the  following 

warranties: 
The  warranty  period  is  24  months  beginning  from  the  hand-over  of  the  device  which 
has to be proved by the original purchasing document. For commercial use and use for 
rent, the warranty period is reduced to 12 months. Wearing parts and defects caused 
by the use of not fitting accessories, repair with parts that are no original parts of the 
manufacturer, use of force, strokes and breaking as well as mischievous overloading of 
the  motor  are  excluded  from  this  warranty.  Warranty  replacement  does  only  include 
defective parts, not complete devices. Warranty repair shall exclusively be carried out 

by authorized service partners or by the company‘s customer service. In the case of any 

intervention of not authorized personnel, the warranty will be held void. 
All postage or delivery costs as well as any other subsequent expenses will be borne by 
the customer. 

Содержание HCS128





































Отзывы: