TOPP DUEVILLE, Инструкция по установке и эксплуатации

Страница: 48 / 60

48
EN INSTRUCTIONS FOR INSTALLATION AND USE DUEVILLE
IT
APPENDIX
6
6.1
MAINTENANCE
6.2
ACCESSORIES AND SPARE PARTS ON REQUEST
@
The duration of the battery pack is affected by the environmental and functional conditions of the automation.
Single wing door up to 120kg -Double wing door up 240kg: Every 1.000.000 cycles
% replace the glide belt.
The words “Wheel replacement” appear on the digital switch :
% replace the rubber stops and guides on the floor of the trolleys
Single wing door from 70 to 100kg - Double wing door up 200kg: Every500.000 cycles
Single wing door from 100 to 140kg : Every 300.000 cycles
Single wing door up to 70kg – Double wing door up to 140kg: Every 1,000,000 cycles
Single wing door from 240 to 280kg : Every 300.000 cycles
% replace the gearmotor and electronics.
%
replace the emergency battery system (after disconnecting the power supply).
Every 250,000 cycles or 1 year (the words “Rubber replacement” appear on the digital switch) : /guides
%
replace the carriage wheels
Single wing door from120 to 240kg - Double wing door up 280kg: Every500.000 cycles
%
if worn, replace the central gaskets and brushes on the doors.
Model K200 DUEVILLE
% with the automation powered, check the stability of the door ensuring that the movement is regular without friction;
disconnect the power supply and check that the emergency battery system opens the doors in the entirety of the
passageway;
Every 1,000,000 cycles (the words “Belt replacement ” appear on the digital switch) :
Every 24 months (the words “Battery replacement” will appear on the digital switch):
Model K280 DUEVILLE
Every 500,000 cycles or 10 years (the words “gear motor/electr. ” appear on the digital switch) :
In order for the automation unit to operate correctly, should be carried out periodical maintenance on the same. This
maintenance activity may be carried out either by TOPP, in accordance with a specific agreement made with the user, or by the
installation technician or by other competent and qualified technical personnel in possession of all legal requirements.
IMPORTANT! – During maintenance operations, the personnel shall be equipped with suitable personal protection equipment
(PPE) so as to perform the works required under safe conditions.
The recommended maintenance activities should in any case involve the periodical execution of at least the following
operations:
Every 6 months (the words “Check/cleaning” will appear on the digital switch):
% clean the glide surface of the carriages and wheels, using a cloth lightly moistened with solvent;
%
clean the glasses of the activation and safety sensors with a cotton cloth slightly moistened with water. Do not use solvents
or other aggressive products;
%
verify the correct operation of the sensors;
%
make sure there are no uncovered areas in the vicinity of the mobile doors that are not detected by the sensors;
%
verify the correct operation of the photocells, if any, the blocking system and their fastenings;
%
check the belt tension, the stability of the automation and the tension of all the screws;
%
check the correct alignment of the doors and position of the door on the jamb when closed;
% check the connections and electric wiring;
At the end of the cycles or data entered manually by the maintenance personnel, the ' hex wrench' symbol will appear on the
display to indicate that maintenance is needed. This 'alarm' can be reset by the maintenance personnel.
%
N.1 Program selection knob (mod. MS1);
%
N.2 Ultra flat wall button;
%
System for glass door;
Do not use spare parts and accessories that are not original as this could affect the safety and efficiency of the automation.
Original spare parts and accessories must be requested exclusively from the authorized retailer or directly from the factory,
communicating the type, model, serial number and year of construction of the automation:
% N.2 Infrared sensors (mod. IS1 and IS2);
%
N.2 Microwave sensors (mod. WS1);
%
N.1 Digital program selector (mod. DS2);
%
N.1 Program selection knob (mod. KC1);
%
N.1 Electromechanical door block;
%
N.2 Miniaturized photocells (mod. F1 and mod F2);
%
Antipanic door opener (simple or complete);
% Lateral sensors.
Should arise the need to use accessories other than those mentioned, the installer can apply directly to our technical support
service.