8
Twintalker 7100 Sport Pack
13.11.2 Sending a call Tone
Press the
button
briefly. The call tone will be transmitted on the set channel.
13.12 Roger Beep On/Off
After the
-button is released, the unit will send out a roger beep to confirm that you have
stopped talking.
To set the Roger Beep.
• Press the
- button
nine times.
‘rO’
will be displayed.
• Press
to enable
(ON)
or
to disable the Roger-Beep
(OF)
.
• Press the
PTT
- button
to confirm your selection and return to the
standby mode.
13.13 Key-Tone On/Off
When a button is pressed, the unit will beep briefly.
To set the key-tone.
• Press
ten times.
‘tO’
will be displayed.
• Press
to enable
(ON)
or
disable the Key Tones
(OF)
.
• Press the
PTT
- button
to confirm your selection and return to the.
standby mode.
13.14 Dual Channel Monitor function
In stand-by, the PMR is set on one channel with CTCSS/DCS code. The PMR will only receive
signals transmitted on that channel with the CTCSS/DCS code.
Dual Channel Monitor (DCM) allows you to monitor a second channel with CTCSS/DCS code.
When the Dual Channel Monitor function is activated, the PMR will switch sequentially between
the standby c CTCSS/DCS code and the Dual C CTCSS/DCS code.
13.15 Button Lock
13.16 Stopwatch function
The Twintalker 7100 has a stopwatch that will count to 59'59''99.
13.17 Display back light
To activate the backlight of the LCD display, press any button except the
PTT
- button
or the
button
.
The LCD backlight will light up for 6 seconds.
14 Earpiece connection
The Twintalker 7100 can be used with the included earpiece.
The connector is located on the upper side of the unit
.
Insert the earpiece plug into the connector (2,5mm jack).
The small button on the earpiece has the same function as the
PTT -
button
on the unit
When you use the
PTT
- button
from the Earpiece, you must also use the microphone from
the earpiece to talk into
.
•
Press the
-button
eleven times,
” DCM OF"
will flash
on the display.
•
Press the
-button
or the
-button
to change the
channel.
•
Press the
-button
to confirm the channel selection
and go to CTCSS selection. (Press the
-button
again to go to DCS selection)
•
Press the
-button
or the
-button
to change the
CTCSS code or DCS code.
•
Press the
PTT
-button
to confirm and return to stand-by
mode.
•
To disable the function select
"OF"
when selecting the DCM
channel.
10
PTT
5
11
11
5
9
6
5
5
9
6
11
•
Press and hold the
-button
for three seconds to
activate the Button lock mode. The button lock icon is
displayed on the LCD Screen.
•
Press and hold the
-button
again for three seconds
deactivate button lock
•
Press the
-button
and hold for three seconds , the
stopwatch display will appear.
•
Press the
-button
to start the stopwatch.
•
Press the
-button
to stop the stopwatch.
•
Press the
-button
to reset the stopwatch to zero.
•
Press the
-button
and hold for three seconds to
deactivate the stopwatch.
5
5
The PTT-button
, the
-button
and the
-button
will still be
functional when the Button Lock is activated
.
11
10
4
10
9
9
6
10
11
10
2
11
11
Do not connect other earpieces. This may damage your device.
