manualshive.com logo in svg

Top Flite FW 190, Инструкция по эксплуатации

Поделиться
Скачать
Top Flite FW 190 Скачать руководство пользователя страница 24

24

the front edge of the plywood cowl ring. For a stronger 
fi llet milled fi berglass can be mixed with the epoxy.

❏

 13. Position the cowl back on the fuselage. Mark 

and trim the cowl from around the cylinder head and 
muffl er. The stock muffl er included with the DLE-55 
engine fi ts great inside the cowl. A Pitts style muffl er 
can also be used.

APPLY THE FINAL DETAILS

❏

 1. Trim the cockpit fl oor along the edge so that it lays 

fl at. Use medium CA to glue the fl oor in the bottom of 
the cockpit. The edge of the fl oor will need a notch cut 
in it to fi t around the former.

❏

 2. Trim the two side panels. Note that the front of each 

panel will need to be trimmed to fi t past the instrument 
panel. Install the decals on the side panels as shown. 

See the decal key on page 34. 

❏

 3. Once satisfi ed with the fi t of the side panels in the 

fuselage, glue them in position. We found that using 
canopy glue along the bottom and aft end of the panels 
worked well. Then, use CA along the top edge to glue 
the side panels under the lip.

❏

 4. Apply the instrument panel decals to the plywood 

instrument panel backplate. Position the backplate 
behind the instrument panel. Adjust the backplate, 
sanding the edges, so that the instrument dials line-
up with the openings.

❏

 5. Glue the instrument panel backplate to the back 

of the instrument panel. Apply the remaining instrument 
decals to the front of the instrument panel as shown. 
See the decal key on page 34.

Содержание FW 190





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды