manualshive.com logo in svg

Top Flite FW 190, Инструкция по эксплуатации

Поделиться
Скачать
Top Flite FW 190 Скачать руководство пользователя страница 11

11

❏

 

❏

 7. Secure the retracts in the wing. Apply a drop of 

threadlocker to the threads of six 6-32 x 3/4" [19mm] 
machine screws and #6 lock washers before threading 
them into the retract plate.

❏

 

❏

 8. Use a sharp hobby knife to remove the covering 

from over the fi ve mounting holes in the plywood retract 
cover. Set the retract cover over the retract and drill a 

1/16" [1.6mm] pilot hole using the holes in the cover 

as a guide. 

❏

 

❏

 9. Mount the retract cover to the wing with fi ve #2 

x 3/8" sheet metal screws and fi ve #2 fl at washers. Use 
thin CA to harden the holes.

❏

 

❏

 10. Snap three of the nylon landing gear door 

mounts onto the landing gear strut as shown. Center 
the landing gear cover over the retract. Check that the 
landing gear door mounts are aligned with the gear door.

❏

 

❏

 12. Drill 1/16" [1.6mm] pilot holes at the screw 

locations in the cover. Secure the landing gear cover 
to the landing gear door mounts with six #2 x 3/8" fl at-
head sheet metal screws. 

Note

 that the landing gear 

cover can be rotated on the landing gear strut. Once 
the wing is installed on the fuselage and the orientation 
of the wheels is checked and correct, the landing gear 
door mounts can be secured to the landing gear struts 
with a drop of thin CA.

❏

 13. Return to step 1 and mount the right retract in 

the right wing.

JOIN THE WING

Note:

 Keep the retracts in the retracted (up) position so 

they do not extend and retract as you handle the wing. 

❏

 1. Use 6-minute epoxy to glue the two 5/16 x 1-1/4" 

[8 x 30mm] wood wing alignment dowels 5/8" [15mm] 
into the root of the left wing half.

Содержание FW 190





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды