www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
13
GB
• Persons working on the machine should not be
distracted.
• Note the direction of rotation of the motor and
saw blade. Use only blades whose permissible
maximum speed is not lower than the maximum
spindle speed of the circular saw and of the
material to be cut.
• After you have switched off the motor, never slow
down the saw blade by applying pressure to its
side.
•
Only fit blades which are well sharpened and
have no cracks or deformations.
• Only use saw blades that are recommended by
the manufacturer, comply with EN 847-1.
• Faulty saw blades must be replaced immediate-
ly.
• Never use saw blades which do not comply with
the data specified in this manual.
• Never dismantle the machines safety devices or
render them inoperative.
• If the table insert is worn, replace it.
• Always stand to the side of the saw blade when
working with the saw.
• Never load the machine so much that it cuts out.
• Make sure that off-cuts do not catch on the saw
blade crown. Risk of catapulting!
• Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
• To rectify faults or remove jammed pieces of
wood, always switch off the machine first. Unplug
the power plug or remove the spark plug connec-
tor!
• If the sawing gap is worn, replace the table in-
sert. Unplug the power plug or remove the spark
plug connector!
• Carry out retooling work, adjustments, measure-
ments and cleaning jobs only when the motor is
switched off. Unplug the power plug or remove
the spark plug connector!
• Before switching on, make sure that all keys and
wrenches have been removed from the tool.
• Switch off the motor and unplug the power plug
before you leave the workplace.
•
Refit all guards and safety devices immediately
after you have completed any repairs or mainte-
nance work.
• Be sure to observe the safety information and
operating and maintenance instructions issued
by the manufacturer, as well as the dimensions
listed in the Technical Data.
• It is imperative to observe the accident preven-
tion regulations in force in your area as well as
all other generally recognized rules of safety.
• Make sure you stand squarely and keep your
balance at all times.
• Check the tool for damage.
• Each time before re-using the tool, carefully
check that the guards or any slightly damaged
parts are working as intended.
• Check that the moving parts are in good working
order, that they do not jam, and that no parts
are damaged. Make sure that all parts are fitted
correctly and that all other operating conditions
are properly fulfilled.
• Unless otherwise stated in the operating instruc-
tions, damaged safety devices and parts must
be repaired or replaced by an authorized service
center.
• Have damaged switches replaced by a customer
service workshop.
• If necessary, wear suitable personal protection
equipment. This could consist of:
- Ear plugs to prevent the risk of damaging your
hearing;
- A breathing mask to avoid the risk of inhaling
hazardous dust.
- Always wear gloves when handling saw blades
and rough materials. Whenever practicable, saw
blades must be carried in a container.
• The operator must be informed about the condi-
tions that influence the generation of noise (for
example saw blades designed to reduce noise
emissions, caring for blades and the machine).
• Faults on the machine or its guards, safety devices
and blade must be reported to the person in charge
as soon as they are discovered.
• Use only the transport devices to move the ma-
chine. Never use the guards for handling and mov-
ing the machine.
• All operators must receive proper training in the
use, adjustment and operation of the machine.
• Do not saw any materials that contain foreign bod-
ies such as wires, cables or ties.
• Only use sharp saw blades.
Use only as authorized
The firewood circular saw is designed exclu
-
sively with the offered tool for the processing of
wood.
The machine corresponds to the valid EC guide-
line.
• The log saw is constructed as 1-man-operating
stand and is only to be used in outdoor locations.
• The log saw is a portable circular saw. It is only
applicable to cross cut firewood with a feeding
rocker according to the technical specifications.
• The saw is constructed solely for cross cutting of
firewood with max. 1 meter length.
• Regardless of the diameter of the wood only 1 work
piece is to be put on the rocker.
• Observe all safety and hazard notes on the
machine and ensure they are kept complete and in
a legible condition.
• The machining range and surrounding areas of the
machine must be clear of interfering foreign matter
to prevent accidents occurring.
• Workpieces must be completely free of foreign
objects, i.e. nails or screws.
