TonerRefillKits ReChargX RX139 Скачать руководство пользователя страница 3

Страница: 3 / 12

TonerRefillKits.com

RechargX™ RX139

Mon - Fri 8am - 5pm ET

2014.07.30

800.527.3712 or 352.343.7533

Page 3 of 12

Step 7: Plug in the Hole-Making Tool

Plug in the hole-making tool included with the

ReChargX™ Tool Kit.

Turn the sand timer over and wait the full three

minutes before using the tool so it reaches

proper operating temperature; this ensures the

tool will easily penetrate the

cartridge hous-

ing (figure 7).

Step 8: Creating the Toner Hopper Hole

While holding the ReChargX™ hole-making tool

directly over the location for the toner hopper

hole, slowly press the copper hole-making bit

against the cartridge until it penetrates the

cartridge housing.

Since the tool is quite hot, excessive force is

unnecessary (figure 8).

Note:

Once the copper tip of the hole-making

tool penetrates the top of the toner cartridge,

immediately withdraw the tool, unplug it from

the wall and proceed to step 9 before the tool is

allowed to cool off.

Step 9: Remove the Excess Plastic From

the Hole-Making Tool

Use the metal tip of the small flat-blade

screwdriver (included in the ReChargX™ Tool

Kit) to remove the small, circular piece of

plastic that will normally remain inside the

copper hole-making bit (figure 9).

Note

: This step needs to be completed before

the hole-making tool cools off. If the plastic

does harden inside the copper bit, plug in the

tool and remove the plastic debris as soon as it

starts to loosen from the bit.

Figure 7

: Wait for the hole-making tool to heat up

Figure 8

: Creating the toner hopper hole

Figure 9

: Removing the excess plastic piece

Содержание ReChargX RX139













Результаты поиска

Содержание ReChargX RX139

Отзывы:

Бренды по названию

Популярные бренды

TonerRefillKits ReChargX RX139, Инструкция по эксплуатации

Результаты поиска

Содержание ReChargX RX139

Отзывы:

Бренды по названию

Популярные бренды