manualshive.com logo in svg

TOHATSU MFS 4B, Руководство пользователя

Поделиться
Скачать
TOHATSU MFS 4B Скачать руководство пользователя страница 35

Replacing the propeller

A worn-out or bent propeller will lower 
the motor's performance, and cause 
engine trouble.
Before removing the propeller, remove 
the spark plug caps from the spark 
plugs  to  protect  against  personal 
injury.

①

 Remove the split pin, propeller nut 

and washer.

②

  Remove  the  propeller  and  thrust 

holder.

③

  Apply  genuine  grease  to  the 

propeller shaft before installing a 
new propeller.

④

 Install the thrust holder, propeller, 

washer and propeller nut onto the 
shaft.

⑤

 Install a new split pin into the nut 

hole and bend it.

35

1

2

3

4

5

6

7

8

9

10

11

12

13

INSPECTION AND MAINTENANCE

Propeller shaft holder

Propeller

Washer

Split pin

Nut

!

�������

Do not hold propeller with hand(s) 
when loosening or tightening propeller 
nut. Put a piece of wood block between 
propeller blade and anti-ventilation 
plate to hold propeller.

!

�������

Do not begin propeller removal and 
installation procedure with spark 
plug caps attached, shift in forward 
or reverse, main switch at other than 
"OFF", engine stop cord attached to 
the switch, and starter key attached, or 
engine could accidentally start leading 
to serious personal injury. Disconnect 
battery cable if possible.

●

Do not install propeller without 

thrust holder, or propeller boss 
could be damaged.

●

Do not reuse split pin.

●

After installing split pin, spread the 

pin apart to prevent it from falling 
out which could lead to the propeller 
coming off during operation.

!

�������

Содержание MFS 4B





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды