manualshive.com logo in svg

TOHATSU MFS 4B, Руководство пользователя

Поделиться
Скачать
TOHATSU MFS 4B Скачать руководство пользователя страница 25

MF, EF type

①

Stop the engine.

②

Shift the outboard into neutral.

③

Raise the engine to the tilt up position.

④

Change the thrust rod position.

⑤

Gentry lower the outboard.

25

1

2

3

4

5

6

7

8

9

10

11

12

13

ENGINE OPERATION

Thrust Rod

Higher

Lower

!

�������

●

Do not put hand or finger in between 

outboard motor body and clamp 
bracket when adjusting trim angle to 
prevent injury in case the outboard 
motor body falls.

●

Unsuitable trim position can cause 

loss of control of boat. 
When testing a trim position, run 
boat slow initially to see if it can be 
controlled safely.

Note

Stop the engine before adjusting trim 
angle.

!

�������

Excessive trim up or down may lead 
to unstable boat operation, potentially 
causing the steering difficulty that 
leads to accident during cruising.

●

Do not cruise at high speed if 

improper trim position is suspected. 
Stop the boat and readjust trim 
angle before continuing cruise.

■

Tilt up

With  the  shift  lever  in  Neutral  or 
Forward,  fully  tilt  the  motor  up 
toward you by holding the tilt handle 
provided at the rear of the top cowl. 
Then lower the tilt lever for locking at 
tilt-up position.

Note

Stop the engine before tilting up.

6. Tilt up, tilt down and shallow water operation

!

�������

When tilting up or down, be careful not 
to place your hand between the swivel 
bracket and the stern bracket.
Be sure to tilt the outboard motor down 
slowly.

Содержание MFS 4B





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды