TOELLNER TOE 9261 Скачать руководство пользователя страница 21

Страница: 21 / 21

Section 5

– Views

TOELLNER Electronic Instrumente GmbH

Views

Front panel view of the

TOE 9261

[1] Mains switch with green

POWER

LED

[2]  8x DIL switch
[3]  Front BNC control input
[4]  Selectable input buffer capacitor with green indication

LED

[5]  Power switch input
[6]  Power switch, longitudinal path incl. red indication LED
[7]  Power switch output
[8]  Selectable base load 10

kΩ or 100 kΩ with green

indication LED

[9] Power switch, branch path incl. red indication LED

[10] 0

Ω series resistor for branch path with green

indication LED

[11] 0.1

Ω series resistor for branch path with green

indication LED

[12] Red

OVL

LED (overload)

[13]  Polarity reminder
[14]  Connections for signal line switches S3 and S4
[15]  Connections for signal line switches S5 and S6

Rear view of the

TOE 9261

[20] Identifier
[21] Protective earth

Do not unscrew!

[22]  Rear BNC control input
[23]  Rating plate
[24]  Mains panel plug, with fuse

Содержание TOE 9261






















Результаты поиска

Содержание TOE 9261

Отзывы:

Бренды по названию

Популярные бренды

TOELLNER TOE 9261, Инструкция по эксплуатации

Результаты поиска

Содержание TOE 9261

Отзывы:

Бренды по названию

Популярные бренды