TOELLNER TOE 9261 Скачать руководство пользователя страница 16

 

Section 3 

– Configuring for 19" rack mount 

 

 

TOELLNER Electronic Instrumente GmbH 

16 

3. 

Configuring for 19" rack mount 

3.1 

19" adapter set (2 HU) for 1x TOE 9261 (option) 

The series 

TOE 9261

 Electronic Switches are 19" rack-capable tabletop devices. By using 

the optional 

TOE 9521

 one 

TOE 9261

 can be easily converted for 19" 2 HU rack mount.  

The optional 19" adapter set 

TOE 9521

 includes a 19" adapter piece with handle and a 19" 

compensation panel with handle as well as the necessary installation materials. 
 

Reconfiguring from 1x TOE 9261 to 19" rack mount 

1.  Use the included TX 20 screwdriver to remove the feet from the Electronic Switch. First 

remove the rubber inserts on the front feet. 

2.  Use the included Allen wrench to remove the two inner screws (6) on the left and right 

side of the front panel of the Electronic Switch. Pull the two fill strips (5) from the side. 

3.  For the left or right side attach 

a handle (4) with countersunk screws (7) to the 19” 

adapter piece (1). Insert this unit in replacement for the fill strip and screw it on to the 
front panel using the hexagon socket screws (6). 

4.  F

or the other side attach the adapter bracket (3) to the 19” compensation panel (2) using 

the hexagon socket screws (6), the spring washers (9), and the nuts (8). Also attach the 
handle (4) with countersunk screws (7) to the 19” compensation panel (2). Insert this pre-
assembled unit in replacement for the fill strip and screw it on to the front panel using the 
hexagon socket screws (6). 

5.  Use the thread-forming screws (10) to attach the adapter bracket (3) of the above-

mentioned unit additionally to the side holes provided as shown in the diagram. 

 

 

 

 

  1:  19" adapter piece 2 HU 
  2:  19" compensation panel 2 HU 
  3:  Adapter bracket 
  4:  Handle 
  5:  Fill strip 
  6:  Hexagon socket screw M3 x 8 
  7:  Countersunk screw M5 x 12 
  8:  Nut M3 
  9:  Spring washer for M3 
 10:  Thread-forming screw 3.9 x 6.5 

 
 

Installing in the 19" rack 

The 19" unit must be located on the device side on a slide rail. This slide rail as well as the 
fasteners needed for attaching the unit in the 19" rack are not included in the scope of 
delivery for this option. 

 

Содержание TOE 9261






















Отзывы: