background image

15

10. SPECIFICATIONS

C-CV454R-3 CU
24 V AC, 50/60 Hz or 12 V DC
4 W (300 mA, Maximum current: 800 mA)

1/3 type IT-CCD
768 (H) x 494 (V), 380,000 pixels

2:1 interlace

Horizontal: 15.734 kHz, Vertical: 59.94 Hz

VBS1.0 V(p-p), 75 

Ω

, RCA pin jack

VBS1.0 V(p-p), 75 

Ω

, Water-resistant connector

Internal synchronization

Horizontal: 540 lines (standard), Vertical: 350 lines

50 dB
0.5 lx (50 IRE, color, High-sensitivity switch OFF),
0.2 lx (20 IRE, color, High-sensitivity switch OFF),
0 lx (night mode)
Color-to-B/W mode: Approx. 2 lx,
B/W-to-color mode: Approx. 10 lx (incandescent lamp)

ATW/AWB (switch selector)

f = 3.0 mm - 9.0 mm

1 : 1.4 - 2.4

Auto iris
Horizontal: 90.3º - 31.9º, Vertical: 66.4º - 23.9º, diagonal: 115.4º - 39.8º
Indoor: Approx. 18 m (59.06 ft) (High-sensitivity switch OFF),

Approx. 25 m (82.02 ft) (High-sensitivity switch ON)

Outdoor:Approx. 15 m (49.21 ft) (High-sensitivity switch OFF),

Approx. 25 m (82.02 ft) (High-sensitivity switch ON)

Backlight compensation, Flickerless function, Iris control, Max.8 x sensitivity increase
(auto/off), Noise reduction (24-hours), Day/Night mode (auto selector),
Adjustment switch: ON/OFF (use for focus adjustment)
IP66

-10ºC to + 50ºC (14ºF to 122ºF)

90%RH or less (no condensation)

Front cover, rear cover, and sunshade: Aluminum, light gray, paint
Mounting bracket: Stainless steel, light gray, paint
ø92 x 230 (D) mm (ø3.62" x 9.06" (D)) (excluding the mounting bracket)
1.2 kg (2.65 lb)

Model Number
Power Source
Power 
Consumption
Image Device
Number of 
Effective Pixels
Scanning System
Scanning
Frequency
Monitor Output
Video Output
Synchronizing 
System
Resolution
(at center)
S/N Ratio
Minimum
Illumination
(Flickerless: OFF)
Threshold 
Illumination for
Mode Switching
White Balance 
Mode
Focal Length
Maximum 
Aperture Ratio
Iris
Angle of View
Infrared LED's
Illumination Range

Functions

Water/Dust
Protection
Operating 
Temperature
Operating
Humidity
Finish

Dimensions
Weight

The design and specifications are subject to change without notice for improvement.

Содержание C-CV454R-3 CU

















Отзывы: