OPTIONAL
JUNCTION
BOX
ANTENNA
CABLE
ANTENNA
Items not supplied
with SRM9000.
SPEAKER
EXTENSION
CABLE
MAJORITY
RED
CABLE
12V
VEHICLE
BATTERY
+
-ve
MAJORITY
BLACK
CABLE
SPEAKER
&
CRADLE
OPTIONAL
MICROPHONE/CONTROL HEAD
EXTENSION CABLE
(3502 310 63290)
LT CABLE
FUSES
TRANSCEIVER
OPTIONAL
HANDSFREE
MICROPHONE
AND CLIPS
S e le c t
On/O f f
F6
F1
F2
F5
F4
F3
x
M
S
SRM9010 SRM9020
BRACKET
SRM9025
PWR
SND
END
M
H
*
O
#
9
8
7
4
5
6
1
2
3
CLR
SEL
ABC
QZ
DEF
GHI
JKL
MNO
PRS
TUV
WXY
OPER
SRM9030
X2 GROMMET
MICROPHONE
& BRACKET
or HANDSET
CONTROL
CABLE
(FRONT)
(REAR)
1
2
3
4
5
6
7
8
9
*
0
#
ABC
DEF
GH I
JKL
MNO
PQ RS
TUV
WXYZ
...
.
BASE
PLATE
CONTROL HEAD BRACKET
(FRONT)
(SIDE)
TRANSCEIVER INSTALLATION
The
Transceiver
is designed to be mounted in the luggage compartment or under the front
seat.
Do not cover the transceiver with carpet, mats or luggage
.
Locate the
Transceiver
in the desired position. A minimum clearance of 20mm around the
Transceiver
is recommended to ensure adequate airflow.
Secure the
Transceiver
in position using the supplied screws. Alternatively, if the Quick
Release Mounting option is used, mount the Cradle in the desired position and clip the
transceiver into the Cradle.
POWER & OPTION CABLING
Run the
LT-Cable
from the installed
Transceiver
to the
Vehicle
Battery
terminals. Ensure
the cable is routed with enough slack so that it is not under tension in its travel. Allow an
extra 0.5m before cutting off excess. Ensure any holes that the cable passes through are
de-burred and fitted with a grommet.
Fit the
Fuses
in both +VE and -VE wires of the cable pair. The
Fuses
are to be fitted within
approximately 0.5m of the
Battery
before the cable has contact with other cables or the
vehicle body. Only 12V, 10Amp, fast blow fuses should be used.
On the DB15
Power/Speaker
connector, connect Pins 3 and 14 as follows:
Pin 3 (Ignition Sense)
Connect Pin 3 to the Ignition Switch wiring such
that +12V is applied when the ignition is switched
ON
and is disconnected when the ignition is
switched
OFF.
Pin 14 (Handsfree Mic)
Refer to separate Installation Instructions for
connection of the Handsfree Microphone.
CONTROL HEAD/HANDSET/MICROPHONE INSTALLATION
The
Control Head
and/or
Microphone/Handset
stowage bracket should be mounted so that
the display and control buttons are readily visible and accessible to the driver when
constrained by a seatbelt. Ensure that these locations are chosen such that the equipment
cannot cause injury in the event of an accident. Ensure that all in-cab equipment is mounted
outside the passenger’s safety zone. Ensure that there is adequate room for cables to exit
the
Control Head
without interference.
Do not locate the
Control Head/Handset/Microphone
on the top of the dashboard or in direct
sunlight as the temperature of exposed surfaces may rise over 100°C in the sun.
Locate the
Handset
/
Microphone
Bracket
where the driver can readily remove or stow the
Handset/Microphone
. Ensure that the curly cord is not stretched when the unit is stowed on
the
Bracket
.
Note:
The
Handset/Microphone Bracket
is proximity sensitive. Certain radio operations
rely on the
Handset/Microphone
being correctly stowed in the stowage bracket
when it is not being used.
The
Control Head Bracket
may be fitted onto the
SRM9030
in two orientations, allowing
extra mounting options. Determine the desired position and secure the
Control Head
Bracket Base Plate
in position
.
Connect the
Microphone
and
Transceiver
Cables
(refer to diagram). Secure the
SRM9030
to the
Mounting
Bracket.
Locate and secure the
Mounting Bracket
to the
Base Plate.
If the Optional
Mic/Control Head Extension Cable
and
Junction Box
are used, locate and
secure the
Junction Box
in a safe convenient location
using the supplied fittings.
