background image

 

172-65417MA-05  (FS21-L/FS21-H  +  BD2)    4  Oct  2021

 

Safety Considerations 

  Read this section carefully before use and be sure to follow the instructions. 

  Installation, inspection, maintenance, repairs, disassembly, adjustment and valve 

opening/closing should be carried out only by trained maintenance personnel. 

  The precautions listed in this manual are designed to ensure safety and prevent 

equipment damage and personal injury. For situations that may occur as a result of 
erroneous handling, three different types of cautionary items are used to indicate 
the degree of urgency and the scale of potential damage and danger: DANGER, 
WARNING and CAUTION. 

 

The three types of cautionary items above are very important for safety: be sure to 
observe all of them as they relate to installation, use, maintenance and repair. 
Furthermore, TLV accepts no responsibility for any accidents or damage occurring 
as a result of failure to observe these precautions.

 

Symbols 

 

Indicates a DANGER, WARNING or CAUTION item. 

 

Indicates an urgent situation which poses a threat of death or 
serious injury 

 

Indicates that there is a potential threat of death or serious injury 

 

Indicates that there is a possibility of injury or equipment / product 
damage 

 

 

NEVER apply direct heat to the float. 

The float may explode due to increased internal pressure, causing 
accidents leading to serious injury or damage to property and 
equipment. 

 

Install properly and DO NOT use this product outside the 
recommended operating pressure, temperature and other 
specification ranges. 

Improper use may result in such hazards as damage to the product or 
malfunctions that may lead to serious accidents. Local regulations 
may restrict the use of this product to below the conditions quoted.

 

 

DO NOT use this product in excess of the maximum operating 
pressure differential. 

 

Such use could make discharge impossible (blocked).

 

 

Take measures to prevent people from coming into direct 
contact with product outlets. 

Failure to do so may result in burns or other injury from the discharge 
of fluids. 

Continued on the next page 

 

 

 

 

DANGER 

 

WARNING 

 

CAUTION 

 

WARNING 

 

CAUTION 

Содержание QuickTrap FS21-H






















Отзывы: