background image

 

172-65510MA-05  (GP Series  System Package)  27  Dec  2016

 

10

 

(4) Exhaust Piping [Se]: 

  Unless problems occur, leave the exhaust pipe connected to the condensate 

receiver as designed. 

  When steam is not used as the motive medium, steam clouds (flash steam) 

may come out from the vent pipe [Sv]. In this case it is possible to disconnect 
the exhaust line from the condensate receiver. 
If the exhaust line has to discharge to atmosphere, a sound level of 
approximately 90 – 100 dB may be emitted from the exhaust pipe discharge 
outlet for two to three seconds. If soundproofing measures are necessary, 
install a silencer. (If the exhaust line is connected to the condensate receiver, 
the sound level will be below 60 dB.)   

(5) Condensate Inlet Piping [Si]: 

  Condensate Inlet Pipe [Si] should be as short and straight as possible so that 

condensate naturally flows down into the 

PowerTrap

  Install a 40-mesh or finer strainer [Ki] on the 

PowerTrap

 condensate inlet pipe. 

The installation should be in a location that allows sufficient space for 
maintenance of the strainer. 

  Install a valve [V] and a bypass valve [Vb] on the condensate inlet pipe. This 

allows operation of the equipment while carrying out maintenance work if the 

PowerTrap

 is

 

malfunctioning or needs maintenance. Use a gate valve for 

valve [V] and a globe valve for the bypass valve [Vb]. 

(6) Condensate Outlet Piping [So], Condensate Recovery Line [Sr]: 

  The flow velocity in the pipe should be considered when determining the pipe 

size. 
Condensate in the 

PowerTrap

 is discharged by the motive medium supply 

pressure. The instantaneous flow through the condensate outlet pipe during the 
discharge operation is between 2 and 40 metric tonnes (530 and 10,600 U.S. 
gal) per hour.   
The instantaneous discharge amount should be considered when determining 
the outlet pipe diameter. For each system package, motive medium supply 
pressure and back pressure instantaneous discharge amount, contact 

. If 

you have the "

PowerTrap

 Design & Data Sheet", installed piping should be the 

size recommended by TLV. 

Содержание PowerTrap GP10-1CJ




















Отзывы: