TLV PowerTrap GP10-1CJ Скачать руководство пользователя страница 19

Страница: 19 / 19

172-65510MA-05 (GP Series System Package) 27 Dec 2016

Product Warranty

1. Warranty Period

One year following product delivery.

2. Warranty Coverage

TLV CO., LTD. warrants this product to the original purchaser to be free
from defective materials and workmanship. Under this warranty, the product
will be repaired or replaced at our option, without charge for parts or labor.

3. This product warranty will not apply to cosmetic defects, nor to any product

whose exterior has been damaged or defaced; nor does it apply in the
following cases:

1) Malfunctions due to improper installation, use, handling, etc., by other

than TLV CO., LTD. authorized service representatives.

2) Malfunctions due to dirt, scale, rust, etc.

3) Malfunctions due to improper disassembly and reassembly, or

inadequate inspection and maintenance by other than TLV CO., LTD.
authorized service representatives.

4) Malfunctions due to disasters or forces of nature.

5) Accidents or malfunctions due to any other cause beyond the control of

TLV CO., LTD.

4. Under no circumstances will TLV CO., LTD. be liable for consequential

economic loss damage or consequential damage to property.

* * * * * * *

For Service or Technical Assistance:

Contact your

representative or your regional

office.

Manufacturer

CO., LTD.

881 Nagasuna, Noguchi
Kakogawa, Hyogo 675-8511 JAPAN
Tel: 81-(0)79 - 427 - 1800

Содержание PowerTrap GP10-1CJ



















Результаты поиска

Содержание PowerTrap GP10-1CJ

Отзывы:

Похожие инструкции для PowerTrap GP10-1CJ

Бренды по названию

Популярные бренды

TLV PowerTrap GP10-1CJ, Инструкция по эксплуатации

Результаты поиска

Содержание PowerTrap GP10-1CJ

Отзывы:

Похожие инструкции для PowerTrap GP10-1CJ

Бренды по названию

Популярные бренды