TLV JL14-X Скачать руководство пользователя страница 12

Страница: 12 / 19

172-65441A-04 (JL14-X/JLH14-X/JLH14-B) 20 Jan 2021

Detaching/Reattaching the Cover from the Body

Part

During Disassembly

During Reassembly

Cover Bolt
(M22



12 pcs)

-Remove with a socket

wrench

-Consult the table of tightening torques and

tighten evenly to the proper torque

Cover

-Lift up to remove

-Make sure to match the direction of the arrow

indicated on the body and cover

Cover Gasket -Remove the gasket and

clean sealing surfaces

-Replace with a new gasket

Cover Bolt

Cover

Cover Gasket

Disassembly/Reassembly of the Air Vent Unit, Connector and Air Vent Pipe

JL14-X/JLH14-X

Part

During Disassembly

During Reassembly

Air Vent Pipe

-Remove with a pipe

wrench

-Wrap 3

– 3.5 turns of sealing tape around the

threads or coat with sealing compound and
screw into trap unit (main valve unit)

-Consult the table of tightening torques and

tighten to the proper torque

Connector

-Remove with a wrench

-Consult the table of tightening torques and

tighten to the proper torque

Spring Clip

-Pinch insides together

and remove from the
X-element guide

-Insert securely into the groove in the X-

element guide

X-element

-Remove from the X-

element guide

-Reinsert after making sure of the proper

orientation

Air Vent Valve
Seat

-Remove with a socket

wrench

-Consult the table of tightening torques and

tighten to the proper torque

X-element Guide -Remove without bending -The X-element must be inserted smoothly

JLH14-B (Option)

Part

During Disassembly

During Reassembly

Air Vent Pipe

-Remove with a pipe

wrench

-Wrap 3

– 3.5 turns of sealing tape around the

threads or coat with sealing compound and
screw into trap unit (main valve unit)

-Consult the table of tightening torques and

tighten to the proper torque.

Connector

-Remove with a wrench

-Consult the table of tightening torques and

tighten to the proper torque

Snap Ring

-Pinch insides together

and remove from the air
vent case

-Insert securely into the groove in the air vent

case

Air Vent Screen

-Remove being careful

not to misshape

-Replace, being careful not to misshape

Содержание JL14-X




















Результаты поиска

Содержание JL14-X

Отзывы:

Похожие инструкции для JL14-X

Бренды по названию

Популярные бренды

TLV JL14-X, Инструкция по эксплуатации

Результаты поиска

Содержание JL14-X

Отзывы:

Похожие инструкции для JL14-X

Бренды по названию

Популярные бренды