TLV DR8-3EP Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 23

background image

172-65613A-03 (DR8-3P/DR8-3EP/DR8-6P/DR8-6EP) 11 Jun 2020

1

Contents

Introduction ....................................................................... 1

Safety Considerations ....................................................... 2

Specifications .................................................................... 4

Acceptable Operating Range ............................................ 4

Correct Usage of the DR8 Direct-acting Pressure
Reducing Valve ................................................................. 5

Configuration ..................................................................... 7

Installation ......................................................................... 8

Adjustment ...................................................................... 11

Maintenance .................................................................... 12

Disassembly .................................................................... 13

Reassembly .................................................................... 18

Troubleshooting .............................................................. 19

EXPRESS LIMITED WARRANTY .......................... 21

Introduction

Thank you for purchasing the TLV DR8 clean steam direct-acting pressure
reducing valve.

This product has been thoroughly inspected before being shipped from the
factory. When the product is delivered, before doing anything else, check
the specifications and external appearance to make sure nothing is out of
the ordinary. Also be sure to read this manual carefully before use and
follow the instructions to be sure of using the product properly.

The TLV DR8 clean steam direct-acting pressure reducing valve has been
developed especially for the food, beverage and pharmaceutical
industries. This product has an angle type structure with special polishing
applied to internal parts to minimize areas for condensate to accumulate,
and prevent contamination inside the product. Additionally this product has
a structure that is easily disassembled to make internal cleaning
convenient.

For products with special order specifications or options, if detailed
instructions for the special order specifications or options are not
contained in this manual, please contact TLV for full details.

This instruction manual is intended for use with the model(s) listed on the
front cover. It is necessary not only for installation but for subsequent
maintenance, disassembly/reassembly and troubleshooting. Please keep it
in a safe place for future reference.

«
1
2
3
4
...
»

Содержание DR8-3EP
























Отзывы:

Нет отзывов

Похожие инструкции для DR8-3EP

Бренд: ZIMO Страницы: 38

Бренд: Access Страницы: 12

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

Бренд: York Страницы: 20

Бренд: Parkside Страницы: 86

Бренд: QUNDIS Страницы: 2

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: Bartlett Страницы: 7

Бренд: C&C Страницы: 17

Бренд: brel-motors Страницы: 2

Бренд: Allen-Bradley Страницы: 16

Бренд: D+H Страницы: 2

Бренд: Ashly Страницы: 1

Бренд: OneFex Страницы: 24

Бренд: Lampert Страницы: 15

Бренд: Intermatic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды