TLV A-COS-10 Скачать руководство пользователя страница 23

 

172-65254MA-04  (A-COS-10)    22  Apr  2020

 

22

 

Product Warranty 

 

1.  Warranty Period 

One year following product delivery. 

2.  Warranty Coverage 

TLV CO., LTD. warrants this product to the original purchaser to be free 
from defective materials and workmanship. Under this warranty, the product 
will be repaired or replaced at our option, without charge for parts or labor. 

3.  This product warranty will not apply to cosmetic defects, nor to any 

product whose exterior has been damaged or defaced; nor does it apply in 
the following cases: 

1)  Malfunctions due to improper installation, use, handling, etc., by other 

than TLV CO., LTD. authorized service representatives. 

2)  Malfunctions due to dirt, scale, rust, etc. 
3)  Malfunctions due to improper disassembly and reassembly, or 

inadequate inspection and maintenance by other than TLV CO., LTD. 
authorized service representatives. 

4)  Malfunctions due to disasters or forces of nature. 
5)  Accidents or malfunctions due to any other cause beyond the control 

of TLV CO., LTD. 

 
4.  Under no circumstances will TLV CO., LTD. be liable for consequential 

economic loss damage or consequential damage to property. 

 

*    *    *    *    *    *    *

 

For Service or Technical Assistance: 
Contact your TLV

 

representative or your regional

 

TLV office. 

   

Manufacturer

 

 

881 Nagasuna, Noguchi 
Kakogawa, Hyogo 675-8511, JAPAN 
Tel: 81

–(0)79–427–1800 

 

Содержание A-COS-10
























Отзывы: