Titan TTL530GBC Скачать руководство пользователя страница 35

Страница: 35 / 36

Troubleshooting

Problem

Possible cause

Fault correction

There is not enough fuel in the fuel tank

Add fuel

The primer has not been pressed at cold

start

Press the primer and restart

The spark plug is wet

Dry the spark plug

Engine does not

start

The spark plug is damaged

Replace the spark plug

There is not enough fuel in the fuel tank

Add fuel

The cutting means are blocked

Remove the blockage

Engine stops

The engine speed don’t fit the terrain

requirements

Increase the engine speed

The cutting means are not sharp

enough

Replace the cutting means.

The cutting means are not fitted

correctly

Fit the cutting means correctly

Cutting height is wrong

Adjust the cutting height

Bad cutting

performance

The cutting/trimming guard is clogged

Clean the cutting/trimming

guard

The cutting means are broken

Replace the cutting means

The flanges on the cutting means are

loose

Tighten the flanges

The flanges on the cutting means are

broken

Replace the flanges

Excessive

vibration/noise or
big smoke came

out

The mixture scale and oil type is wrong

Re-fill fuel and oil mixture into

the tank

43CC PETROL BRUSH CUTTER TTL530GBC

Содержание TTL530GBC





































Результаты поиска

Содержание TTL530GBC

Отзывы:

Похожие инструкции для TTL530GBC

Бренды по названию

Популярные бренды

Titan TTL530GBC, Инструкция по безопасности и эксплуатации

Результаты поиска

Содержание TTL530GBC

Отзывы:

Похожие инструкции для TTL530GBC

Бренды по названию

Популярные бренды