background image

12

 

Troubleshooting 

Example 1: 

Difficulty starting the eng

ine.

 

1. Make sure the choke lever is in the "on" position (page 7).

2. Remove the fuel in the tank, and replace it with fresh gasoline.

3. Press the fuel bubble 3-4 times.

4. Check to make sure the on/off switch is in the down position.

5. Check the fuel filter (page 8).

6. Check the air filter (page 8).

7. Check the spark plug (page 11).

Example 2:

 Difficulty starting after a sudden stop. 

1.

Check the fuel level.

2.

Check to make sure the on/off switch is in the down position.

3.

Check the fuel filter  (page 8).

4.

Check the spark plug (page 11).

Example 3:

 

Engine lacks power.

 

1.

Check the air filter (page 8).

2.

Check the spark plug (page 11).

3.

Check the fuel lines and fuel filter (page 8).

Example 4:

 Post driver is

 not performing efficiently.

1.

Be sure to hold 10-12 pounds of downward pressure while driving posts.

2.

Try different throttle positions to find the best speed for your application.

Use the throttle limit screw to dial in the best throttle setting.

3.

Check the driver impact grease level. 1-2 tablespoons max (page 10).

4.

Check the condition of the O-rings.

Example 5:

 

The starter rope will not pull.

 

1. Make sure the driver has been in the horizontal position for at least 5 minutes.

2. Check the engine oil.

a. If low, add oil.

b. If too full, remove excess oil and follow the steps below.

*If the driver was overfilled with oil, or engine was stored upside down for long periods of time,

oil can seep into the combustion chamber and cause it to become hydrolocked.

Follow the steps below to resolve this issue.

i. Remove the top cover from the engine.

ii. Remove the spark plug wire.

iii. Remove the spark plug.

iv. Place a small rag near the spark plug hole to catch any oil that may seep out.

v. Slowly pull the starter rope.

vi. Continue until all oil has been removed from the cylinder.

*WARNING: Oil may shoot from the spark plug hole as you pull the starter rope.

If these steps do not address your issue, call Titan Post Drivers at 

(702) 293-4262

 for further assistance. 

Содержание PGD2875H























Отзывы: