background image

12 
 

Every 10 hours of use:

 

1.  Check the grease level of the driver as described in Step 3 of the 

First 10 Hours Use 

guidelines. 

Every 3 months or 25 hours of use:

 

1.  Change the engine oil following the guidelines in your Honda GX35 manual. Dispose of 

discarded oil in accordance with all local, state, and federal regulations. 

DO NOT 

OVERFILL.

 

2.  Replace air filter. This should be performed more often if your post driver is operated in 

dusty conditions. 

3.  Check all engine and post driver fasteners and retighten if necessary. If you choose to 

replace or reinstall any bolts with new Loctite, follow the guidelines listed above pertaining 
to Loctite. Follow any torque requirements. 

 

Every 12 months or 250 hours of use:

 

1.  Follow the above regularly scheduled maintenance guidelines for every 3 months or 25 

hours of use. 

2.  Follow the above regularly scheduled maintenance guidelines for every 4 months or 50 

hours of use. 

3.  Remove and service the hammer and anvil according to guidelines in the 

Servicing of 

Hammer and Anvil

 section. 

4.  Replace all O-rings and housing seals. A rebuild kit including all the Viton O-rings, seals, 

grease, and Loctite is available from Titan Post Drivers. 

The amount and type of grease used in your Titan Post Driver is critical for the performance and 
service life of your post driver. Not enough grease will cause failure, and too much grease will 
overburden the piston and affect the hammering power of the machine. Use only Titan-approved EP 0 
grease, which is available from Titan Post Drivers.   

ALWAYS

 

reassemble your driver fasteners using 

LOCTITE BLUE 243

. Remember to clean the 

fastener and the holes with a parts cleaner to remove all grease residue, or the Loctite will not be 
effective.  

If you are unsure of anything in this manual, please contact Titan Post Drivers directly at (702) 293-
4262.  

If you are experiencing performance issues with your Titan Gas-Powered Post Driver, please refer to 
the 

Troubleshooting 

section of this manual for possible solutions or contact Titan Post Drivers for 

assistance. 

 

 

Содержание PGD2000

























Отзывы: