background image

10 
 

Service and Maintenance  

The Titan Gas-Powered Post Driver has been manufactured and designed to give you years of trouble-
free post driving. Always refer to the Honda GX35 manual for service and maintenance guidelines on 
your engine. The following maintenance guidelines will keep your machine in top-performing condition.  

Be sure to properly store your Titan Post Driver. 

DO NOT

 lay it horizontally on the driver side or resting 

on the engine. The recommended method of storing is in an upright position, however, if this is not 
possible, place it on a flat surface with the barrel and brush-guard supporting the machine at an angle, 
so that the top handle is the highest point.   

If you are experiencing an issue with the Honda engine, please contact your local Honda dealer 

for parts and service. Titan Post Drivers does not carry the engine parts for Honda, nor does 
Titan Post Drivers determine the warranty, which is honored by Honda. 

 

Before each use:

 

1.  Check the engine oil level by holding the machine in an upright position. Lying the machine 

down to check the oil will give you a false reading. Use SAE 10W-30 oil to top off if 
necessary. 

2.  Check the engine air filter. If it is overly soiled, clean or replace it. 
3.  Check all post driver fasteners and retighten if necessary. If you choose to reinstall any 

bolts with new Loctite, you must clean the bolt and the area of the bolt hole with parts 
cleaner to remove any grease residue. The Loctite will not be effective if grease is present. 
Follow any torque requirements. 

4.  Visually check the inside of the barrel and the anvil for any debris or foreign objects. 
5.  Check for any fluid leaks. 

First 10 hours use:

 

1.  Change the engine oil following the guidelines in your Honda GX35 manual. Dispose of 

discarded oil in accordance with all local, state, and federal regulations

DO NOT 

OVERFILL. 

Always check the oil level by holding the machine in an upright position. 

2.  Check all engine and post driver fasteners and retighten if necessary. If you choose to 

replace or reinstall any bolts with new Loctite, follow the guidelines listed above pertaining 
to Loctite. Follow any torque requirements. 

3. 

CHECK GREASE:

 For continuous, hard pounding and/or when the driver body is hot to the 

touch, check the grease level of your driving in the following manner: 

Remove the crank housing cover to check the EP 0 grease level. The crank area 
should look clean and grease should be visible around the crank area and on top of 
the piston. There should be a ring of grease collected against the wall of the crank 
case. 

ii 

If the ring of grease around the crank case wall measures less than ¼”, it is an 
indication that the grease level is low. Add no more than a few tablespoons of 
TITAN EP 0 grease (NON-APPROVED GREASE TYPES WILL CAUSE THE 
MACHINE TO NOT OPERATE CORRECTLY AND WILL VOID YOUR 
WARRANTY). 

You never want to exceed ½” of grease ring around the crank case 

Содержание PGD2000

























Отзывы: