13
Step 5: Håndtag
Step 5.
Use Screw Driver attach the Handlebar
(5a&5b ) onto lower handlebar with the
Carriage Bolts(56) and washers(57) and
Cap Nuts(58).
Step 4.
Take off the Nylon nut(61) and
washers(77) from from the axles of the
upright tube(3).Take off the
bolts(55),washers(77) and nylon nuts(61)
from the pedal tube arm(54).Attach the end
of the steeves(4a&4b) to the axle on the
upright tube(3) with washers(77) and nylon
nuts(61) that are just taken off from the
axles of the upright tube(3) .Attach one end
of the pedal tubes onto the pedal tube
arm(54) on the Main Frame(1) with
bolts(55),washers(77) and nylon nuts(61)
that are just taken off from the pedal tube
arm(54).Cover the nut cap(62) onto the
nylon nuts(61).
3
56
4a
58 57
56
4b
58
5a
57
5b
4b
6a
61
4a
61
3
6b
61
Step 6.
Insert the pulse wires(75) into the bigger
hole on the upright tube(3) and pull them
out from the top of the upright
tube(3).Then attacht the U-style bar(89)
onto the tube(3) and fix it with the
screws(13) and washers(52).
Connect pulse wire(75) and sensor wire(49)
to the wire of computer(8), and attached the
computer(8) to the end of upright post(3).
fixed the computer with bolt (98)
62 64
62
64
13
8
98
98
49
Step 6: Pulshåndtag og computer
Step 5.
Use Screw Driver attach the Handlebar
(5a&5b ) onto lower handlebar with the
Carriage Bolts(56) and washers(57) and
Cap Nuts(58).
Step 4.
Take off the Nylon nut(61) and
washers(77) from from the axles of the
upright tube(3).Take off the
bolts(55),washers(77) and nylon nuts(61)
from the pedal tube arm(54).Attach the end
of the steeves(4a&4b) to the axle on the
upright tube(3) with washers(77) and nylon
nuts(61) that are just taken off from the
axles of the upright tube(3) .Attach one end
of the pedal tubes onto the pedal tube
arm(54) on the Main Frame(1) with
bolts(55),washers(77) and nylon nuts(61)
that are just taken off from the pedal tube
arm(54).Cover the nut cap(62) onto the
nylon nuts(61).
3
56
4a
58 57
56
4b
58
5a
57
5b
4b
6a
61
4a
61
3
6b
61
Step 6.
Insert the pulse wires(75) into the bigger
hole on the upright tube(3) and pull them
out from the top of the upright
tube(3).Then attacht the U-style bar(89)
onto the tube(3) and fix it with the
screws(13) and washers(52).
Connect pulse wire(75) and sensor wire(49)
to the wire of computer(8), and attached the
computer(8) to the end of upright post(3).
fixed the computer with bolt (98)
62 64
62
64
13
8
98
98
49
Monter de to håndtag (5a, 5b) for
oven på hver svingarm (4a, 4b).
Benyt bolte (66) samt spændeskiver
(57) og hættemøtrikker (58).
Træk
pulsledningerne
(75)
ind
gennem hullet på uprighten og træk
dem ud gennem hullet for oven.
Monter derefter pulshåndtaget (89) til
uprighten
med
bolte
(13)
og
spændeskiver (52)
Pak computeren (8) ud og afmonter
de fire skruer (98) som er monteret
på
bagsiden.
Forbind
pulsledningerne (75) til de tilsvarende
stik fra computeren. Forbind derefter
øverste computer-ledning (49) til
stikket fra computeren.
Pas på, at
benene i stikket ikke bøjes eller
knækkes.
Put ledningerne ned i hullet på
uprighten og monter computeren med
de fire skruer (98).
