background image

Setup

Read, understand, and follow all warnings before starting
or operating this sprayer.

1. Connect the siphon hose to the fluid section and the bleed

hose to the bleed valve.  They each have factory installed

PTFE

 tape on the male end of the hoses and should be

tightened wrench tight.

2. Attach a minimum of 50’ of nylon airless spray hose to the

unit.  Do not use 

PTFE

 tape or thread sealant on the

spray hose connection.

3. Attach an airless spray gun to the spray hose.  Do not

attach the tip to the spray gun yet.  Remove the tip if it is
already attached.

a. To use two guns, remove the plug from the second gun

outlet on the filter assembly.  Connect a hose and gun
to the outlet.

4. Fill the wet-cup 1/2 full with Speeflo

Piston Lube (P/N 314-480) supplied
by the factory. This extends packing
life. 

5. Check the hydraulic fluid level daily

before starting the unit.  The hydraulic fluid level should be
at the “Full” mark on the dipstick.  Refer to the
Maintenance section of this manual for hydraulic system
maintenance instructions.

Use of Speeflo's Coolflo™ Hydraulic Fluid (P/N 430-361) is
mandatory in the hydraulic system.  Do not use any other
hydraulic fluid. Use of any other hydraulic fluid may
seriously damage the hydraulic system and will void the
warranty.

CAUTION

NOTE: This unit is engineered

to handle up to 3 guns
with .022" tips.  For
multiple gun operation,
connect a multiple gun
manifold to the single
gun outlet.  Connect a
hose and gun to each
outlet.  Make sure the
second gun outlet
remains plugged.

Multiple Gun 

Manifold

Bleed 
Hose

Siphon Hose

Bleed Valve

Fluid Section

WARNING

6

© Titan Tool Inc.  All rights reserved.

6. For gas models, check the engine oil level daily before

starting the unit.  The gasoline engine oil level is
determined by the engine manufacturer.  Refer to the
engine manufacturer’s service manual supplied with this
unit.

7. For electric models, use a 20 amp service outlet.  Always

locate the electric model within 10 to 15 feet of the service
outlet.  Use a short electric cable and a long paint hose.
Any extension cord will create some voltage drop.  If an
extension cord is necessary, use only a grounded 3-wire
#12 extension cord.

8. Make sure the unit is grounded. All units are equipped

with a grounding lug.  A grounding cable (not supplied)
should be used to connect the unit to a true earth ground.
Check your local electrical regulations for detailed
grounding instructions.  See the Accessories and Service
Kits section near the back of this manual for grounding
cable ordering information.

Proper grounding is important.  This applies to both gas
and electric powered models.  The passage of some
materials through the nylon fluid hose will build up a
static electric charge, which if discharged, could ignite
solvent vapors present and create an explosion.

9. Strain all paints with a nylon strainer to ensure trouble free

operation and freedom from frequent cleaning of the inlet
screen and gun filter.

10 Make sure the spray area is well ventilated to prevent

hazardous operation with volatile solvents or exhaust
fumes.

If lacquer or other flammable materials are to be sprayed,
ALWAYS locate the unit outside the immediate spraying
area. Failure to do so may cause an explosion.

11. Locate the unit outside the immediate spraying area to

avoid clogged air intake of the engine or electric motor
with overspray.

WARNING

WARNING

NOTE: If the unit is being operated in an area that is

overloaded by other appliances or low voltage
conditions, it is important to start the unit
"unloaded."  Tip the electric motor forward so
that the belt is loosened and the motor starts
without full load.  This reduces the amperage
draw on starting and may avoid tripping the
circuit breaker.

Содержание 335-305

































Отзывы: