background image

1

1-SAFETY

INSTRUCTIONS

1.1 INTRODUCTION

•   The lift may be installed and commissioned by authorized service personnel only.

•   The standard lift version may not be installed and commissioned in the vicinity of 

explosives or flammable liquids, outdoors or in moist rooms (e.g. car wash).

•   Read this entire manual.

•   Load should not exceed rated capacity for this lift – 13,000 lb (3,250 lb per lift arm)

•   Only trained authorized personnel over the age of 18 years should operate the lift.

•   Indoor use recommended.

•   Always lift the vehicle using all four arms.

•   Never use the lift to raise one end or one side of vehicle.

 

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN  

PROPERTY DAMAGE.

 WARNING: 

READ ENTIRE MANUAL AND COMPLY WITH ALL SAFETY AND SERVICE 

PRECAUTIONS. DEATH, PERSONAL INJURY AND / OR PROPERTY DAMAGE MAY OCCUR IF 

INSTRUCTIONS ARE NOT FOLLOWED CAREFULLY.

Personal injury and property damage incurred due to non-compliance with these safety 

instructions are not covered by the product liability regulations.

 

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL 

INJURY.

SYMBOLS

 

IMPORTANT INFORMATION

1.2 SAFETY INSTRUCTIONS FOR COMMISSIONING

1.3 SAFETY INSTRUCTIONS FOR OPERATION

Содержание HD2P-13KCL









































Отзывы: