background image

 

Loop (B2)

 - Loop On/Off (‘LOOP’) turns the looping on and off by holding this 

button and then using the Tempo knob.

Loop Start (B3)

 - Loop Start (‘LPSt’).  Select the 

Bank

 and 

Preset

 for the loop to 

begin.  

Loop End (B4) 

- Loop End (‘LPEn’).  Select the 

Bank 

and 

Preset 

for the end of 

the loop.  

Note 

: Loops can run forward or backwards.  Also note that the internal 

Cycle

 

must be set to a non-zero value or the external 

Reset In

 must be triggered for the 

presets to change.

BPM/CYCLE:

 This button toggles between the following functions:

1) Tempo (‘bPm’) - sets the Tempo in Beats Per Minute (BPM)

2) Cycle  End(‘CYCE’) - sets the internal Reset count.  0 sets the counter up              

   to infinity. Values from 1 to 255 will reset the counter after that many               

   clocks and, as mentioned earlier, is a great way to make things sound more  

   repetitive.

3) Cycle Start (‘CYCS’) - the value the clock resets to from 1 to 255.  Setting a 4  

   will make a division of 4 fire immediately on reset.  This allows alignment with 

   other devices like x0x style sequencers.

Note: After a timeout the knob returns to setting Tempo in BPM. Whatever was set 

is saved.

START/STOP:

  Starts and Stops the internal clock. Displays ‘Strt’ and ‘Stop’ on the 

display. On Start it sends a reset pulse on the Reset out jack to synchronize other 

sequencers.  Hold the button down to access these features: 

1) Clock Source: Select from Internal (‘Int’), External (‘EXt’), SyncBus (‘SYNC’) and 

Circadian Rhythms (’Cr’). Internal clock source is default.

2) Clock Rate: DIN Sync, DAW or 16th notes for 

Clock In

 and 

Clock Out. 

DIN is used to sync with Roland TR series devices only, DAW has a high resolution 

24 PPQN rate suitable for sync with a computer. 16th notes is default and the rate 

used by most Eurorack sequencers.

3) Reset First/Last : Set reset to fire on the first count or the last count of a 

cycle. First is default

Each button hold cycles thru these three functions and pressing the button once 

exits and returns to BPM. After 20 seconds it times out and returns to BPM.

12

Содержание Trigger Riot























Отзывы: