15
E
N
G
L
I
S
H
14
E
N
G
L
I
S
H
Marker Disassembly / Assembly:
NOTE: If you are not proficient in the
disassembly and assembly of paintball markers, we suggest having these services
performed by an authorized Tippmann
®
Technician. Do not use power tools to
disassemble or assemble this marker. Hand start screws and bolts and do not
over tighten and strip threaded parts. First follow unloading and air supply removal
instructions on page 13. Do not pressurize a partially assembled paintball marker.
Put the marker in the uncocked position. If marker is cocked, hold the bolt cocking
handle - then pull the trigger and release handle forward
to uncock the marker.
Bolt = 1 1/16”
Bolt = 7/8”
Bolt = 5/8”
Bolt = 1/2” Flat Head
Bolt = 1/2” Round Head
Screw = 1/2” +Head
Bolt = 5/8”
Screw = 1/2” +Head
Disassembly / Assembly (continued from page 14)
Disassembly / Assembly (continued on page 16)
Disassembly / Assembly (continued on page 15)
❏
TO CHECK THE RECEIVER INTERNAL PARTS:
❏
Remove the Front Grip
Cover
(or Front Grip
on XT and eXT).
❏
Remove the front Grip bolt
=(1/2” rounded head) and slide Front Grip Cover
(or Front Grip
)
off. NOTE: It is not necessary to disassemble the 2 front Grip Halves at any time.
❏
To Remove the Receiver Cover
:
❏
Remove the 2 screws
/
(1 from left side and 1 from right side) holding the Receiver Cover. At
these 2 points, spread Receiver Cover apart enough to carefully slide it
off the front of the receiver while observing how its inner guides align to
the guides of the receiver (NOTE: at reassembly you will spread apart
and slide the cover into place with guides aligned the same way).
❏
To remove the barrel
: twist the barrel counterclockwise.
❏
To remove the Grip Frame
:
❏
Remove 2 tank adapter bolts
=(7/8”) to
disconnect the tank adapter
.
❏
Remove the Battery Cover bolt
=(5/8”)
and pull battery cover
off.
❏
Remove the 2 Grip Frame
bolts
=(1 1/16”) /
=(1/2”)
and
❏
remove the Grip Frame
by carefully tilting it side to
side as you work it down off
the receiver lug
, back and
out of the receiver
.
❏
GAS LINE ACCESS:
The Gas line
(or Gas
Line with In Line Expansion
Chamber
on models XT
and eXT) is located in the
Mid-Grip
.
❏
To remove Mid-Grip
from the receiver:
❏
Remove 2 bolts
=(5/8”)
holding it to the receiver.
(Nuts for these 2 bolts
will remain in place in
right Mid-Grip half and
need not be removed).
❏
Remove 4 screws
holding Mid-Grip halves
together.
❏
Lift left Mid-Grip half
off and
❏
right Mid-Grip half
will
come off right side. (NOTE: At reassembly, place square nut
in right
Mid-Grip half. Also be sure tank adapter alignment lug-pin
fits into
both left and right Mid-Grip halves).
❏
To remove Tank Adapter
from the gas line
: (NOTE: it is not
necessary to remove the tank adapter to disassemble the receiver.) Hold
the Gas Line fitting with a wrench and unscrew tank adapter
from it.
❏
Reinstalling Tank Adapter
to the gas line
:
❏
Check the gas line
o-ring and if damaged, replace with a new one. Clean and oil the gas line o-ring.
❏
Hold Gas Line fitting with wrench and hand start Tank Adapter onto gas
line fitting and slowly screw it on until tank adapter aligns with bottom of
Grip Frame and is snug (do not over tighten and strip threaded parts).
