Timberwolf TW 125PH, Руководство пользователя

Страница: 44 / 44

V-BELT TENSIONING TABLE
43
METHOD:
TIPS ON BELT TIGHTENING:
13/75G
18/100G
125PH
150DH/DHB
150FTR
150VTR
190DH
190FTR
190TDH
190TFTR
190TVGTR
230TR
250DH
PTO100
PTO150
PTO300
S425/S426
SHREDDER
Belt Mfr / Type
Gates Super
HC-MN
Gates Super
HC-MN
Gates Super
HC-MN
Gates Super
HC-MN
Gates Super
HC-MN
Gates Super
HC-MN
Gates Super
HC-MN
Gates Super
HC-MN
Gates Super
HC-MN
Gates Super
HC-MN
Gates Super
HC-MN
Gates Quad
Power II
Gates Super
HC-MN
Gates Super
HC-MN
N/A
Gates Super
HC-MN
Belt Pitch Designation
SPA
SPA
SPA
SPA
SPA
SPA
SPA
SPA
SPA
SPA
SPB
XPB
SPA
SPA
SPB
Belt Length
900.0
1060.0
1060.0
1060.0
1060.0
1060.0
1232.0
1232.0
1232.0
1232.0
1950.0
3350.0
900.0
900.0
2120.0
Belt deflection
=
h
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
6.0
10.0
4.0
4.0
8.0
3.4 - 3.6
3.1 - 3.3
3.0 - 3.2
4.3 - 4.5
4.3 - 4.5
4.3 - 4.5
3.3 - 3.5
3.3 - 3.5
3.9 - 4.1
3.9 - 4.1
3.4 - 3.6
3.5 - 3.7*
3.3 - 3.5
3.8 - 4.0
3.3 - 3.5*
3.0 - 3.2
2.8 - 3.0
2.7 - 2.9
3.7 - 4.0
3.7 - 4.0
3.7 - 4.0
2.8 - 3.0
2.8 - 3.0
3.4 - 3.6
3.4 - 3.6
3.0 - 3.2
3.1 - 3.3*
2.9 - 3.0
3.3 - 3.5
2.9 - 3.1*
Belt Mfr / Type
N/A
N/A
Gates Super
HC-MN
N/A
Gates Super
HC-MN
Gates Super
HC-MN
N/A
Gates Super
HC-MN
N/A
Gates Super
HC-MN
Gates Super
HC-MN
N/A
N/A
Gates Super
HC-MN
Gates Super
HC-MN
N/A
Belt Pitch Designation
SPA
SPA
SPA
SPA
SPA
SPA
SPA
SPA
Belt Length
950.0
900.0
900.0
925.0
925.0
950.0
950.0
1000.0
Belt deflection
=
h
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
1.9 - 2.0
2.3 - 2.4
2.3 - 2.4
2.3 - 2.4
2.3 - 2.4
1.5 - 1.6
2.0 - 2.2
1.9 - 2.0
1.7 - 1.8
2.0 - 2.1
2.0 - 2.1
2.0 - 2.2
2.0 - 2.2
1.3 - 1.4
1.8 - 2.0
1.7 - 1.8
* DUE TO THE EXTENDED BELT SPAN LENGTHS ON THE 250DH & S425/S426 SHREDDER, THE FORCE READINGS ARE INCREASED BY 0.5Kgf OVER THE
DESIGN IQ OUTPUTS
Force reading (Kgf)
New belt Used belt
TW MODEL No.:
PUMP BELT
Used belt
Force reading (Kgf)
RO TOR BE LTS
TIMBERWOLF V-BELT TENSIONING DATA TABLE
1. SET THE DEFLECTION DISTANCE ON THE LOWER SCALE OF THE TENSION GUAGE SO THAT THE UNDERSIDE OF THE 'O'-RING EQUALS THE 'h' VALUE GIVEN IN THE TABLE BELOW 2. ENSURE THAT THE DEFLECTION FORCE SCALE IS ZERO'D BY PUSHING THE UPPER 'O'-RING ALL THE WAY DOWN 3. PLACE THE TENSION GUAGE IN THE CENTRE OF THE BELT SPAN AS SHOWN IN THE DIAGRAM LEFT 4. PRESS DOWNWARDS ON THE RUBBER BUFFER, DEFLECTING THE BELT UNTIL THE UNDERSIDE OF THE LOWER O'-RING IS LEVEL WITH THE BELT BEHIND (USE A STRAIGHT EDGE IF THERE IS ONLY 1 BELT) 5. TAKE THE READING FROM THE DEFLECTION SCALE OF THE TENSION METER (READ AT THE LOWER EDGE OF THE 'O'-RING) & COMPARE THIS VALUE WITH THAT GIVEN IN THE TABLE BELOW 6. TIGHTEN OR LOOSEN BELTS AS REQUIRED FOLLOWING PROCEDURE GIVEN IN THE OPERATOR'S MANUAL TENSION GUAGES ARE AVAILABLE FROM TIMBERWOLF SPARES, QUOTING PART No. 18091
New belt
A) THERE WILL NORMALLY BE A RAPID DROP IN TENSION DURING THE RUN-IN PERIOD FOR NEW BELTS. WHEN NEW BELTS ARE FITTED, CHECK THE TENSION EVERY 2-3 HOURS & ADJUST UNTIL THE TENSION REMAINS CONSTANT B) THE BEST TENSION FOR V-BELT DRIVES IS THE LOWEST TENSION AT WHICH THE BELTS DO NOT SLIP OR RATCHET UNDER THE HIGHEST LOAD CONDITION C) TOO MUCH TENSION SHORTENS BELT & BEARING LIFE D) TOO LITTLE TENSION WILL AFFECT THE PERFORMANCE OF YOUR MACHINE ESPECIALLY IN RESPECT OF NO-STRESS DEVICES E) ENSURE THAT BELT DRIVES ARE KEPT FREE OF ANY FOREIGN MATERIALS F) IF A BELT SLIPS - TIGHTEN IT!
=
=
h
Ver 2.0 - 12-10-07