Timberk TEC.PS1 LE 2000 IN, Инструкция по эксплуатации

Страница: 6 / 23

www.timberk.com • electric convector heater www.timberk.com • electric convector heater
11
10
at that the “Normal” comfort mode indicator and value of the last
set temperature will be shown on the display. While the temperature
setting is blinking, press button “ ” or “ ” to set the desired
temperature.
3.5. After the desired temperature is set, the last set value will be stored
and the display will show the current temperature.
4. Select the operation mode
4.1. Press button “ ” once to select the economy operation mode, at that
green “Economy” indicator will be illuminated on the control panel. In
this mode the convector will automatically maintain the set economy
mode temperature, switching on and off heating from time to time.
4.2. Press button “ ” twice to select the comfort operation mode, at
that orange “Normal” indicator will be illuminated on the control panel.
In this mode the convector will automatically maintain the set comfort
mode temperature, switching on and off heating from time to time.
4.3. Press button “ ” three times to select the antifreeze mode, at
that symbol “AF” will be shown on the display. The convector will
automatically maintain temperature within the range +5°C to +7°C,
switching on and off heating from time to time.
5. Set the convector switch off timer function
5.1. When the convector is operating press button “ ” four times, at that
yellow “Timer” indicator will start blinking on the control panel, and the
display will show blinking value [0.0] or the last set value of the timer.
5.2. Press button “ ” or “ ” to set the convector switch off time,
in increments of 1 hour, from 0 to 24 hours. The display will show the
countdown of time left until the convector is switched off.
5.3. The set time value will be stored and in 3 seconds the system will
automatically return to indicating the temperature value, at that yellow
“Timer” indicator will be illuminated on the control panel.
5.4. The convector will be switched off after the timer expires, indicators on
the control panel and temperature indication on the display will go out,
at that red “Power” indicator will be on.
5.5. Switching off the unit or setting the timer value [0] will cancel the
convector switch off timer function.
6. Set the convector switch on timer function
6.1. When the convector is switched off and only red “Power” indicator is
illuminated, press button “ ” and “ ” simultaneously, at that a
sound signal will be given, yellow “Timer” indicator will start blinking on
the control panel, and the display will show two small dots.
6.2. Press button “ ” or “ ” to set the convector switch off time, in
increments of 1 hour, from 0 to 24 hours. The display will show the
countdown of time left until the convector is switched on.
6.3. The set time value will be stored and then two small dots will be shown
on the display and yellow “Timer” indicator will be illuminated on the
control panel.
6.4. The convector will be switched on to operate in the economy mode
after the timer expires, and will maintain the set temperature.
7. Audio signal
An audio signal is given when the convector is switched on and off, as
well as the buttons are pressed.
8. Lock
8.1. When the convector is operating, to lock the system simultaneously
press and hold buttons “ ” and “ ” for 3 seconds, after that
symbol “_” will be shown on the display. In 3 seconds the temperature
value will be shown, at that buttons on the control panel will be locked,
and symbol “_” will be shown when they are pressed.
8.2. To unlock the system, press and hold buttons “ ” and “ ” for 3
seconds or switch off the convector.
9. Air ionizing function
The convector is equipped with an air ionizer.
9.1. You can switch on and off the air ionizer by means of the ionizer button
“ ”.
9.2. A blue “Ionizer” air ionizer indicator is illuminated when the air ionizer
is switched on.
9.3. The air ionizer is a completely independent device and can operate
even when the unit’s heating mode is off.
10. “RESTART” function
In case of a short-term power outage, the convector will be
automatically switched on and will operate with the last user settings
(except for timer settings) after power supply is restored.
11. Convector switching off
To switch off the convector, press and hold button “ ” on the control
panel for 3 seconds, then set the power switch, located on the side of
the control panel, to “OFF” position.
Operating TEC.PS1 RCE…IN series convector heater by means of
remote controller
1. Convector switching on
Connect the convector to electric mains by plugging the power cord
into an electric outlet, set the power switch, located on the side of the
control panel, to position “ON”, at that red power indicator “Power” will
be illuminated on the control panel and a sound signal will be given,
then press “POWER” button on the remote controller. The convector
heater will be switched on and start operating in the comfort mode
(“ ” symbol), with factory comfort mode temperature setting of 24°C
and high heating power (“ ” symbol).
2. Heating power mode selection
Press “MODE” button several timer to select low or high heating power.
“ ” symbol will be shown on the remote controller’s display if low
heating power is selected, and “ ” symbol will be shown on the remote
controller’s display if high heating power is selected.
3. Temperature setting
3.1. Temperature can be set within the range +5 to +30°C, in increments
of 1°C.
3.2. Factory setting of the comfort mode temperature is +24°C, factory
setting of the economy mode temperature is +17°C.
3.3. To change the economy mode temperature, press “SET” button once,
At that the “ ” economy mode symbol will be shown on the remote
NOTE:
A small static electric charge may be accumulated on
metal surfaces of a case in units, equipped with an
air ionizer.
If your electric main has no grounding circuit or it is
damaged. In this case there is a small possibility of
electric shock from static voltage.
IMPORTANT!
If the unit is operated without a grounding circuit or it
is damaged, it is not recommended to switch on and
operate the air ionizer.
controller’s display and value of the last set temperature will start
blinking. While the temperature setting is blinking, press button “ ” or
“ ” to set the desired temperature.
3.4. To change the comfort mode temperature, press “SET” button
twice, at that the “ ” comfort mode symbol and value of the last set
temperature will be shown on the remote controller’s display. While the
temperature setting is blinking, press button “ ” or “ ” to set the
desired temperature.
3.5. After the desired temperature is set, the last set value will be stored
and the remote controller’s display will show the current temperature.
4. Operation mode selection
4.1. Press “SET” button once to select the economy operation mode, at
that “ ” symbol will be shown on the remote controller’s display. In
this mode the convector will automatically maintain the set economy
mode temperature, switching on and off heating from time to time.
4.2. Press “SET” button twice to select the comfort operation mode, at that
“ ” symbol will be shown on the remote controller’s display. In this
mode the convector will automatically maintain the set comfort mode
temperature, switching on and off heating from time to time.
4.3. Press “SET” button four times to select the antifreeze mode, at that
“ ” symbol will be shown on the remote controller’s display. The
convector will automatically maintain temperature within the range
+5°C to +7°C, switching on and off heating from time to time.
5. Convector switch off timer function setting
5.1. When the convector is operating press “SET” button three times, at
that “ ” and “OFF” symbols will be shown on the remote controller’s
display and time setting will start blinking.
5.2. Press “ ” or “ ” button to set the convector switch off time, in
increments of 1 hour, from 0 to 24 hours. The remote controller’s
display will show the countdown of time left until the convector is
switched off.
5.3. The set time value will be stored and the remote controller’s display will
show “ ” and “OFF” symbols.
5.4. Setting the timer value to [00] will cancel the convector switch off timer
function.
6. Convector switch on timer function setting
6.1. When the convector is switched off and only red “Power” indicator is
illuminated, press “SET” and “MODE” buttons simultaneously, at that