Timberk TEC.PS1 LE 2000 IN, Инструкция по эксплуатации

Страница: 5 / 23

www.timberk.com • electric convector heater www.timberk.com • electric convector heater
9
8
Operation of TEC.PS1 LE…IN, TEC.PS1 RCE series convector
heater
1. Switch on the convector
Connect the convector to electric mains by plugging the power cord
into an electric outlet, set the power switch, located on the side of the
control panel, to position “ON”, at that red power indicator “Power” will
be illuminated on the control panel and a sound signal will be given, then
press button “ ”.
2. Select the heating power mode
Press button “ ” several timer to select the low or high heating power.
“LOW” symbol will be displayed if the low heating power is selected,
and “HI” symbol will be displayed if the high heating power is selected.
3. Set temperature
3.1. Temperature can be set within the range +5 to +30°C, in increments
of 1°C.
3.2. Factory setting of the comfort mode temperature is +24°C, factory
setting of the economy mode temperature is +17°C.
3.3. To change the economy mode temperature, press button “ ”
once, at that the “Economy” mode indicator and value of the last
set temperature will be shown on the display. While the temperature
setting is blinking, press button “ ” or “ ” to set the desired
temperature.
3.4. To change the comfort mode temperature, press button “ ” twice,
IMPORTANT!
If the unit is operated without a grounding circuit or it
is damaged, it is not recommended to switch on and
operate the air ionizer.
illuminated. When the room temperature reaches the desired level, turn
the thermostat handle counterclockwise until the unit is switched off, the
“heating” indicator light will go out. Now the thermostat will maintain the
set temperature, switching on and off the convector from time to time.
During especially cold weather the convector may not be able to provide
the required room heating. In this case set the thermostat to the level
somewhat higher than the desired one.
4. “Antifreeze” mode
Turn the thermostat handle counterclockwise to position “ ”. The
thermostat will automatically switch on heating of the convector, if the
room temperature goes below +5°C and the unit is connected to electric
mains and the heating mode is on.
5. “Comfort” mode
“Comfort” mode, which can be selected by means of the thermostat
handle, corresponds to the most comfortable room temperature.
6. Air ionizing function
The convector is equipped with an air ionizer.
6.1. You can switch on and off the air ionizer by means of the ionizer
switch (“Ionizer”), located on the control panel.
6.2. Ionizer switch illumination lights up when the air ionizer is switched on.
6.3. The air ionizer is a completely independent device and can operate
even when the unit’s heating mode is off.
1. Button “ ”
It is used to switch on and off the convector heater.
2. “Power” indicator
It is illuminated at turning on the power switch when the unit is connected
to electric mains.
3. “Normal” comfort mode indicator
It is illuminated when the convector heater is operating in the comfort
mode.
4. LED-display
LED-display can show temperature settings, heating power modes and
timer settings.
5. “Ionizer” air ionizer indicator
It is illuminated when the air ionizing function is activated.
6. Ionizer button “ ”
It is used to turn on/off air ionizing.
7. Button “ ”
It is used to select the following operation modes: low power (“LO”
symbol), high power (HI symbol).
8. “Economy” mode indicator
It is illuminated when the convector is operating in the economy mode.
9. Button “ ”
It is used to increase the selected value.
10. Button “ ”
NOTE:
A small static electric charge may be accumulated on
metal surfaces of a case in units, equipped with an
air ionizer.
If your electric main has no grounding circuit or it is
damaged. In this case there is a small possibility of
electric shock from static voltage.
TEC.PS1 LE…IN and TEC.PS1 RCE…IN series control panel (Fig. 9)
Fig. 9
Fig. 10
It is used to decrease the selected value.
11. Timer indicator “ Timer ”
It is illuminated when the convector switch off timer function is activated.
12. Button “ ”
It is used to select the economy mode (“Economy” indicator), comfort
mode (“Normal” indicator), antifreeze mode (“AF” symbol), as well as
to set the timer.
13. Power switch
It is used to switch on/off the convector heater.
TEC.PS1 RCE…IN series remote controller (Fig. 10)
1. LCD display
It displays temperature, timer settings, as well as unit’s operation
symbols and operation symbols.
2. Button “ ”
It is used to increase the selected value.
3. Button “MODE”
It is used to select the following heating power modes:
low power (“ ” symbol)
high power (“ ” symbol)
4. Button “ ”
It is used to decrease the selected value.
5. Button “POWER”
It is used to switch on/off the convector heater.
6. Button “SET”
It is used to select the economy mode (“ ” symbol), comfort mode
(“ ” symbol), antifreeze mode (“ ” symbol), and to set the timer.
7. Button “ION”
It is used to switch on/off the air ionizing function.