manualshive.com logo in svg

Tiffen Steadicam M-2, Системное руководство, Страница: 8 / 54

Поделиться
Скачать
Tiffen Steadicam M-2 Скачать руководство пользователя страница 8

8

T

he dovetail lock system 

is designed to ensure reliable camera safety. Mounting and removing the 

camera on the M-Series stages encourages you to keep at least one hand on the camera at all times, 

until it is securely fastened. With your camera mounted to the dovetail plate, follow these steps:

The stage is ready for the camera 

plate. Note that the dovetail lock 

and clamp lever are both open.

Place the dovetail against the 

passive side of the clamp, and tilt 

the plate into the dovetail lock.

The weight of the camera will 

press the lock down and release 

the safety latch. You’ll hear a 

satisfying click!

The camera and plate can be 

moved fore and aft for coarse 

balancing, but the safety stops 

prevent it from sliding off.

Close the clamp lever to firmly 

secure the dovetail and camera to 

the stage.

NOTE: 

If the dovetail lock has been pressed down while the dovetail plate was out, you 

will have to slide the safety latch to the right to reopen the lock. Click!

Camera dovetail clamp

Содержание Steadicam M-2























































Отзывы:

Нет отзывов