Tiffen Steadicam M-2 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 54

Tiffen Steadicam M-2 Скачать руководство пользователя страница 36

Monitor Pivot

180˚ range for unobstructed views

Adjustable friction

Post Clamp Lever

Over-center, tools free lock

Open and un-thread to release

Shown here closed

Monitor Block

s

Locate pivot ne

ar the monitor

’s CG

Available for many dif

ferent monitors

Contact Tif

fen for details

Universal Monitor Mount

Adjustable width and height

Monitor Rods

LWS 15mm by 60mm spacing

Standard 1/2”-13 threaded ends

Rod Clamp Levers

Lock or release the monitor rods

Post Clamp

Hinged quick-release

Opens 180˚

Rod Stops

Prevent it going bye-bye!

Simply threaded in

Pivot Clamp Knob

Secure tilt angle of mount

NOTE:

The monitor mount section of this user guide covers product number 158MB-UMM, for 1.58” posts. For product number

175MB-UMM, for 1.75” posts, refer to the original M-1 manual (LIT-815000.)

Lower Post Brake

To mount monitor clamp on lower post

Monitor mount components

«
...
34
35
36
37
38
...
»

Содержание Steadicam M-2























































Отзывы:

Нет отзывов