Tiffen Steadicam M-2 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 54

Tiffen Steadicam M-2 Скачать руководство пользователя страница 16

T

he dovetail clamp

creates tremendous clamping force with very little pressure at the clamp lever. When

the rig is new, get accustomed to the feel of each mechanism so that you can determine if one needs

attention later. The ideal adjustment will not allow the dovetail to slide, even with the heaviest camera, but

remains easy to close fully.

Begin with the dovetail installed,

and the clamp lever closed.

Use a 7/64” Allen wrench to loosen

the lock screw approximately one-

half turn.

Turn the adjustment wheel to dial

in the tension. Turn clockwise

to tighten, counterclockwise to

loosen. Make small adjustments.

Re-tighten the lock screw before

testing the clamp.

Test to see if the dovetail clamp

holds firmly by trying to move the

dovetail plate with your hands.

Test the clamp lever movement.

Repeat adjustment if necessary.

NOTE:

Never mess with the small set screws along the sides of the stage!

Adjustments and maintenance

«
...
14
15
16
17
18
...
»

Содержание Steadicam M-2























































Отзывы:

Нет отзывов