Thytronic SME70-O Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 35

background image

22

SME70-O-Manual-04-2020

—

Cables in the terminal box

Insert the signal cables for each sensor in the three fittings making them out of the junction box and

block the ends of the corrugated tube in the corrugated tube couplings.

—

Mounting the corrugated tube between the junction box and the UP cabinet - wall installation

• Drill a hole with a diameter of 25 mm in the lower side of the SME-UP cabinet and mount the corru-

gated tube couplings, the Nylon locknut M25 with flat gasket.

• Cut the remaining tube for connection between the junction box and the SME-UP cabinet and fix it

to the coupling at the bottom of the junction box.

• Insert the three signal cables into the tube between the junction box and the UP cabinet, taking

care to protect the connectors. Use, if necessary, a cable-guide probe and space the connectors

in order to limit the overall dimensions.

• Block the ends of the tube into the couplings previously installed on the SME-UP cabinet.

• Fix the tubes with suitable clamps (not supplied).

SME70-O

UP

Nylon corrugated tube coupling
Nylon locknuts M25
flat gasket

P1

P2

DN28 Nylon

corrugated tube

CVS-P-24-O RGDAT

support shelf
for sensors

«
...
20
21
22
23
24
...
»

Содержание SME70-O




































Отзывы:

Нет отзывов

Похожие инструкции для SME70-O

Бренд: L-Sniper Страницы: 12

WV-CP500 series

Бренд: Panasonic Страницы: 2

Бренд: Rae Страницы: 49

Бренд: UbiBot Страницы: 11

Бренд: Parklio Страницы: 29

Бренд: iCamera Страницы: 58

Бренд: Dahua Страницы: 18

Бренд: sewerin Страницы: 102

Бренд: HAKO Страницы: 6

Бренд: Campbell Страницы: 26

Бренд: Viewse Страницы: 42

Бренд: jablotron Страницы: 2

Бренд: ADEMCO Страницы: 40

Бренд: Elmes Electronic Страницы: 2

Бренд: Dorlen Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: ELRO Страницы: 4

paddy 000121300000

Бренд: Menabo Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды