background image

3

RECOMMENDED TOOLS & MATERIALS

Adhesives

- You will need two types of adhesives for this ARF - 

Epoxy and Instant (cyanoacrylate) adhesives.We recommend that you
purchase both 5-minute and 30-minute epoxy to cut down on 
assembly time, but you can get by with only 30-minute epoxy if time
is not important.You will also need a small bottle of both “Thick” and
“Thin” instant adhesive.

Tools

-  Model assembly can be much easier if the proper tools are

used. Therefore, we have included in our checklist to the right,
a complete listing of all the tools we used to assemble our prototype
models. As you will notice, many household tools can be utilized 
during construction.

Engine

-  The Thunder Tiger PRO-61 or 91 is the ideal engine for this

airplane. It is a quiet running engine that is easy to start and require no
special break- in period, is very easy to maintain, and will last for years.

Flight Equipment

-  There are several “support” items that you will

need to purchase in order to get your engine running and your plane
in the air.

Comprehensive Items Needed Check List

4-Channel Radio with 4 Standard Servos

5-Minute Epoxy (4 ounces or so)

30-Minute Epoxy (4 ounces or so)

“Thin” Instant Adhesive (1/2 ounce)

“Thick” Instant Adhesive (1/2 ounce)

Hobby Knife and Blades

Epoxy Mixing Sticks and/or Brushes

Sandpaper (150 grit)

Masking Tape

Rubbing Alcohol

Paper Towels

Ruler

Waxed Paper

Fine-Point, Felt-Tip Pen 

Misc. Household Tools

Drill and Bits (1/16”, 1/8” , 9/64”,1/4”, 5/16” )

Flight Equipment

Foam Rubber Padding for the radio

Stick on Lead Strip for balancing the plane

3 or 4 Props (see engine instructions)

10%-15% Glow Fuel

Fuel Pump or Bulb

Electric Starter or “Chicken Stick”

Glow Plug Clip and Battery

Extra Glow Plug(s) 

CCAARRRRYY

M

MAASSTTEERR

A Breakthrough in Field Equipment!

The CarryMaster’s “Organization Plus” allows you to transport all your
field essentials in a rugged and compact case that will fit about
anywhere in about any vehicle. A complete “turn-key” combo is
available as well as the case by itself.
Combo contents include:

• 3 liter fuel cell
• 12v starting battery/charger
• glow starter/charger

• 12v HD starter
• 4-way wrench

Содержание Cloud Dancer 60 ARF

















Отзывы: