Thrane&Thrane Explorer 727 Скачать руководство пользователя страница 134

Страница: 134 / 148

Appendix 5: Troubleshooting

98-126882-B

Status signaling

126

03600 to
03609

2-wire
operational
failure

The Phone/Fax interface
fails to operate, for one of
the following reasons:

Ground shorted.

Power overload.

Temperature overload.

Check the wires.

Wait until the event is
cleared; then try again.

08002

One or more
ports has PoE
disabled due
to power
limitations

The power supply to the
terminal has dropped
critically. PoE is disabled to
ensure enough power to
the antenna.

Ensure a stable power
supply to the terminal.

08008

Antenna
exceeds
voltage
threshold

The antenna voltage is
either too high or too low.

Check the cable to the
antenna.

Contact your distributor if
the problem persists.

08009

Power Hold-up
- the terminal
can no longer
power the
antenna

The power supply to the
terminal has dropped for
too long. The antenna does
not have enough power to
function.

Ensure a stable power
supply to the terminal.

0800A

Reduce PoE -
the terminal
reduces PoE
with 30W

The input voltage to the
terminal is too low. The
terminal will lower PoE
power from 60 W to 30 W.

Ensure a stable power
supply to the terminal.

0800B

PoE
Overvoltage
protection is
activated

Overvoltage is detected in
the terminal. The terminal
will be shut down in 10
minutes.

Do not use the terminal.

Contact your distributor.

0800D

Antenna
Overvoltage
protection is
activated

Overvoltage is detected in
the antenna. The terminal
will be shut down in 10
minutes.

Do not use the terminal.

Contact your distributor.

Event Text

Explanation

Remedy

Содержание Explorer 727





















































































































































Результаты поиска

Содержание Explorer 727

Отзывы:

Похожие инструкции для Explorer 727

Бренды по названию

Популярные бренды

Thrane&Thrane Explorer 727, Руководство пользователя

Результаты поиска

Содержание Explorer 727

Отзывы:

Похожие инструкции для Explorer 727

Бренды по названию

Популярные бренды