THORLABS TLD001 Скачать руководство пользователя страница 50

Страница: 50 / 55

Page 47

17874-D03

T-Cube Laser Diode Driver

Appendix B Preventive Maintenance

B.1

Cleaning

The panel may be cleaned with a soft cloth, lightly dampened with water or a mild

detergent.

Warning: Risk of Electrical Shock

The equipment contains no user serviceable parts. There is a risk of electrical

shock if the equipment is operated with the covers removed. Only personnel

authorized by Thorlabs Ltd and trained in the maintenance of this eq uipment

should remove its covers or attempt any repairs or adjustments. Maintenance

is limited to safety testing and cleaning as described in the following sections.

Warning

Disconnect the power supply before cleaning the unit.
Never allow water to get inside the case.
Do not saturate the unit.
Do not use any type of abrasive pad, scouring powder or solvent, e.g. alcohol

or benzene.

Содержание TLD001
























































Результаты поиска

Содержание TLD001

Отзывы:

Бренды по названию

Популярные бренды

THORLABS TLD001, Руководство пользователя Kinesis

Результаты поиска

Содержание TLD001

Отзывы:

Бренды по названию

Популярные бренды