manualshive.com logo in svg

THORLABS TLD001, Руководство пользователя Kinesis

Поделиться
Скачать
THORLABS TLD001 Скачать руководство пользователя страница 34

Page 31

17874-D03

T-Cube Laser Diode Driver

5.3

Set Up Preparation

The  following  procedure  assumes  that t he  laser  diode  is mo unted  in  a Th orlabs

LM14S2, LDM56, LDM90, or LDM21 diode mount. If this is not the case, care must

be  taken  to en sure  that  the  laser  diode  is  connected  to  the  rear  panel  D-Type

connector with the correct polarity - refer to Section 3.3.4. for more details. A power

meter equipped with a suitable sensor is also required.
1) Insert the laser diode into the diode mount, taking care to observe the correct

orientation.

2) Set the switches on the diode mount to select the correct polarity (AG or CG) for

the diode being used.

3) Using cable CAB400, connect the diode mount to the TLD001 unit.
4) Connect the TLD001 to the power supply.
5) Connect the power meter sensor to the diode mount.
6) Ensure that the KEYSWITCH on the TLD001 is set to OFF, then turn on the power

to all units.

7) Connect the TLD001 unit to the control PC.
8) Run  the  Kinesis  software - Start/Al l  Programs/Thorlabs/Kinesis/Kinesis.  The

server registers automatically the units connected on the USB bus and displays

the associated GUI panels as shown in Fig. 5.1..

Fig. 5.1   Laser Driver Software GUI

Содержание TLD001
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды