THORLABS PM5020 Скачать руководство пользователя страница 52

Страница: 52 / 65

Page 48

MTN028837-D02

PM5020 Dual-Channel Benchtop Power and Energy Meter

Chapter 4 Operating Instructions

4.11.3.2.2 RS232 Operation

The power meter PM5020 can be operated with serial communication via RS232.

Connect the PM5020 power meter using an appropriate connector cable.

Go to the

Settings Menu

and open the submenu Interface

The below screen "Serial" provides the information to connect the PM5020 to the network.

Please use a RS232 standard protocol for RS232 communications. For questions, please contact our engin-
eers at

Thorlabs

Please set up the port as follows:

Parameter

Setting

Baud Rate

115.200 Bit/s (default)

Supported range of Baud Rate: 9.600 and 230400 Bit/s

Data Bits

Parity

None

Stop Bits

Flow Control

None

Termination Character

LF (x0A; \n). The termination character needs to be enabled.

Access to Dirver the SCPI condes to establish remote control software can be found int eh chapter Write
Your Own Application (

WYOA

Содержание PM5020

































































Результаты поиска

Содержание PM5020

Отзывы:

Бренды по названию

Популярные бренды

THORLABS PM5020, Руководство пользователя

Результаты поиска

Содержание PM5020

Отзывы:

Бренды по названию

Популярные бренды