background image

 

INTUN Tunable Laser 

 

12372-D02, 12/15/2007 

Page 38 

www.thorlabs.com 

Part 9.  Regulatory 

As required by the WEEE (Waste Electrical and Electronic Equipment Directive) of the European 
Community and the corresponding national laws, Thorlabs offers all end users in the EC the possibility 
to return “end of life” units without incurring disposal charges. 

 

This offer is valid for Thorlabs electrical and electronic equipment: 

 

Sold after August 13th 2005  

 

Marked correspondingly with the crossed out “wheelie bin” logo (see) 

 

Sold to a company or institute within the EC  

 

Currently owned by a company or institute within the EC  

 

Still complete, not disassembled and not contaminated 

As the WEEE directive applies to self contained operational electrical and electronic products, this end 
of life take back service does not refer to other Thorlabs products, such as: 

 

Pure OEM products, that means assemblies to be built into a unit by the user (e. g. OEM laser 
driver cards)  

 

Components  

 

Mechanics and optics  

 

Left over parts of units disassembled by the user (PCB’s, housings etc.).   

If you wish to return a Thorlabs unit for waste recovery, please contact Thorlabs or your nearest dealer 
for further information. 

9.1.  Waste Treatment is Your Own Responsibility 

If you do not return an “end of life” unit to Thorlabs, you must hand it to a company specialized in waste 
recovery. Do not dispose of the unit in a litter bin or at a public waste disposal site. 

9.2. Ecological 

Background 

It is well known that WEEE pollutes the environment by releasing toxic products during decomposition. 
The aim of the European RoHS directive is to reduce the content of toxic substances in electronic 
products in the future. 

The intent of the WEEE directive is to enforce the recycling of WEEE. A controlled recycling of end of 
live products will thereby avoid negative impacts on the environment. 

Wheelie Bin Logo

 

Содержание INTUN TL 1550-T









































Отзывы: