THORLABS INTUN TL 1550-T Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 40

THORLABS INTUN TL 1550-T Скачать руководство пользователя страница 35

INTUN Tunable Laser

12372-D02, 12/15/2007

Page 35

www.thorlabs.com

Part 6. Maintenance and Service

This chapter describes the recommended preventive and corrective maintenance for the INTUN TL-T.

6.1. Transporting, Storage, Packaging, and Unpacking

A Radians INTUN TL-T tunable laser source module is a delicate device that is sensitive to cold,
humidity, condensation, and shock. It is therefore important to follow these unpacking and packing
instructions carefully. The INTUN TL-T is sensitive to humidity and rapid variations of temperature,
which can cause damage to the INTUN TL-T.

Note that the INTUN TL-T module must be shipped and stored within the following environmental
specifications:

ETS 300 019-1-1.1: Storage in partially temperature-controlled locations where the temperature is
always between -10 to 50 °C (14 to 122 °F).

ETS 300 019-1-2.1: Very careful transport.

The INTUN TL-T should always be transported inside its original packaging, which is special designed
for the INTUN TL-T. In addition, the INTUN TL-T unit should always be stored in a vertical position.
Detailed information about proper packing, unpacking, and transporting the INTUN TL-T are found in a
separate document that comes with the INTUN TL-T.

Warning!

Carefully read the transporting, storage, packing, and unpacking instructions before you

open any shipment containing an INTUN TL-T module.

6.2. Cleaning

To obtain the specified performance, it is very important that the fiber optical connector is clean. Always
clean the optical connector with a proper cleaning tool prior to operating the laser.

«
...
33
34
35
36
37
...
»

Содержание INTUN TL 1550-T









































Отзывы:

Нет отзывов