THORLABS EDU-OT3 Скачать руководство пользователя страница 39

Страница: 39 / 94

Portable Optical Tweezers Kit

Chapter 5: Setup and Adjustment

Page 36

MTN024417-D02

Camera Assembly

Figure 23 shows the components for the lens 3 assembly. Mount the LB1676 lens to the

CP33(/M) cage plate using two retaining rings.

Lens 3 Components

Next, attach the FES0650-IC bandpass filter to the CP33T(/M) thick cage plate. Figure 24

shows the necessary components. Note that the filter has a defined direction of light

propagation. This is marked on the frame of the filter with a small white arrow. This arrow

should be pointing up during assembly.

Bandpass Filter Components

Figure 25 shows the components for assembling the top part of the camera system.

•

First, unscrew one of the locking rings from the SM1T2 lens tube coupler. Next,

screw the SM1L15 lens tube to the coupler and tighten the locking ring. Screw

the SM1NT1 slotted locking ring onto the coupler (do not tighten it).

•

Second, screw the SM1T2 lens tube coupler to the CS165CU(/M) camera with

the slotted locking ring facing the camera but do not tighten it yet. After this, screw

the other side of the lens tube onto the SPT1C(/M) slip plate positioner (with the

locking screws facing towards the camera).

•

Third, connect the CP33(/M) cage plate to the C1498(/M) post clamp using an

SD1 counterbore adapter and an 8-32, 1/2" long (M4 x 12 mm) cap screw.

•

Finally, place the SPT1C(/M) and CP33(/M) onto each other and slip four ER3

cage rods through them (with the rods’ setscrews removed on both sides). Ideally,

the cage rods ends should be flush with the upper side of the SPT1C(/M). Attach

them both to the rods by tightening the cage locking screws at the side.

Содержание EDU-OT3































































































Результаты поиска

Содержание EDU-OT3

Отзывы:

Похожие инструкции для EDU-OT3

Бренды по названию

Популярные бренды

THORLABS EDU-OT3, Руководство пользователя

Результаты поиска

Содержание EDU-OT3

Отзывы:

Похожие инструкции для EDU-OT3

Бренды по названию

Популярные бренды