Thonk Eurorack DIY Kit Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 17

background image

December 14th 2018

www.thonk.co.uk

6

PROK DRUMS

Eurorack DIY Kit

Instructions

Version 1

10.

Now  using  tweezers  or  snipe
nose  pliers  -  take  the  voltage
regulator  and  position  it  flat  on
the  surface  of  the  PCB  as
shown.

Then  re-heat  the  pad  that  we
already  applied  solder  to,  and
when the solder is heated - slide
the regulator into position so that
the  three  pins  line  up  with  the
other  pads  (see  next  image).  If
you don’t manage this first time
round you can re-flow the solder
and  reposition  the  regulator
again.

NOTE!

Make

sure

the

component

is

flush

and

perpendicular to the PCB
surface as you slide it in place.

NOTE:

Do not heat this part excessively

or you will damage it, you should be
aiming to solder quickly and neatly.

11.

Once you have positioned the
regulator it should look as
shown.

«
...
4
5
6
7
8
...
»

Содержание Eurorack DIY Kit


















Отзывы:

Нет отзывов

Похожие инструкции для Eurorack DIY Kit

Future Impact I

Бренд: Panda-Audio Страницы: 2

Бренд: Elenco Electronics Страницы: 160

PartaSaund PCS-30

Бренд: Yamaha Страницы: 20

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 56

Бренд: Waldorf Страницы: 22

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 320

Бренд: NEON CAPTAIN Страницы: 66

Бренд: Yamaha Страницы: 20

16 Bit Digital Percussion Synthesizer XD-5

Бренд: Kawai Страницы: 64

Бренд: MOGlabs Страницы: 64

Бренд: Blind Monk Instruments Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды