Thonk Eurorack DIY Kit Скачать руководство пользователя страница 14

Страница: 14 / 17

December 14th 2018

www.thonk.co.uk

PROK DRUMS

Eurorack DIY Kit

Instructions

Version 1

37.

Next bend the leads for the two
remaining 27K resistors and then
place them standing into R10
and R21 as shown.

NOTE:

Make sure you solder the

resistor bodies as shown in the
picture – with the bodies on
opposite sides.

38.

Now take the remaining 56K
resistor and solder it standing up
into R20 as shown.

NOTE:

Be sure to solder the

resistor body as shown in the
picture with the lead facing the
PCB edge.

39.

Next  locate  the  round  switch
button.  Note  that  one  side  is
flattened.  This  needs  to  match
the  flat  edge  on  the  PCB
silkscreen.

The  real  button  does  not  have
red stripes

BUTTON FLAT EDGE

SILKSCREEN FLAT EDGE

Содержание Eurorack DIY Kit


















Результаты поиска

Содержание Eurorack DIY Kit

Отзывы:

Похожие инструкции для Eurorack DIY Kit

Бренды по названию

Популярные бренды

Thonk Eurorack DIY Kit, Инструкция по эксплуатации

Результаты поиска

Содержание Eurorack DIY Kit

Отзывы:

Похожие инструкции для Eurorack DIY Kit

Бренды по названию

Популярные бренды