THOMSON ROC 3205 - AVEC CODES, Руководство пользователя

Страница: 3 / 24

EN
1
1 - Description of
the key functions
1 Indicator lamp: the red indicator lamp lights up
when any key is pressed.
2 Product keys ( TV , DVD or SAT ): Used to
programme and control different products (TV,
satellite receiver, DVD player and so on).
3 SHIFT : activates the secondary key features
(indications in blue).
4 VOL- , VOL+ Increases ( + ) or decreases ( - ) the
volume of the TV set;
SHIFT +
C
/
B
: also allows you to navigate the
menus horizontally.
5 :Teletext On/Off in TV mode.
SHIFT + MENU : turns on the menu of the
selected products
6
G
(rewind): Goes backward or advances
forward ( DVD )*.
7 RECORD : To record, press the RECORD key
twice.
8 Stop the disc ( DVD )*.
9 Number keys 0 to 9: these keys have the same
functions as those of your original remote and
are also used to enter the codes for different
products.
10 : stop page scrolling (videotext).
11 SETUP : Programmes the remote control.
12 POWER : On/Standby.
13 AV : For selecting an external source (SCART).
14 PROG+ , PROG- : Programmes zapping button
(received by the television set or the satellite
receiver); use to scroll vertically through menus.
SHIFT + / : also allow you to navigate the
menus vertically.
15 MUTE : Switches the TV sound off.
SHIFT + OK : confirms a selection.
16 :Teletext Off in TV mode.
SHIFT + EXIT : turns off the menu of the
selected product.
17
B
(play): play a DVD disc DVD *.
18 F : fast forward ( DVD )*.
19 K : Suspends play and stops on an image*.
20 :Videotext inlay on TV picture.
21 Press this key first before you type in the 2-digit
channel number (except for Thomson group
products).
* The coloured buttons can be used to select
categories when teletext is activated, and specific
functions depending on the make.
2 - Testing the remote control
before you programme it
1. Turn on the product you want to control.
2. Press the product key ( 2 ) that corresponds to the
type of product you want to control:
TV : television set, DVD : DVD player,
SAT : satellite receiver.
3. Point the remote control towards the product and
try to turn it off by pressing the POWER ( 12 ) key.
If the product doesn’t turn off, you’ll need to
programme the remote control by one of the
methods described in chapter
3 .
3 - Programming
the remote control
Method A – Fast programming
with 1-digit subcode
Before you start programming, you must find the subcode
of the product to be controlled (television set, satellite
receiver or DVD player).
Refer to the list provided with these instructions, page I of
the
codes .
1. Turn on the product you want to control.
2. Hold down the
SETUP ( 11 ) key until the red
indicator lamp ( 1 ) remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes when this time is almost up, and then
goes off).
3. Press the product key ( 2 ) that corresponds to the
type of product you want to control:
TV : television set, DVD : DVD player,
SAT : satellite receiver.
4. While the indicator is lit, type in the subcode
(example: 1 for THOMSON).
5. Point the remote towards the product and try to
turn it off by pressing the POWER ( 12 ) key.
6. If the product you want to control turns off, press
the MUTE ( 15 ) key to save the subcode.
7. If the product doesn’t turn off, press the POWER
( 12 ) key repeatedly until the set switches off. Wait
approximately one second between key presses to
give the red indicator lamp (
1 ) enough time to go
off and light up again. This will allow you to see
whether the product responds or not.
8. Immediately after the product to be controlled
turns off, press the MUTE ( 15 ) key to save the
subcode.
Note:
If you want to assign another type of product than those
mentioned on the remote control (with the exception of the
TV button which can only be used to control a television
set), begin by entering the code that corresponds to the
product you want to programme (a 3-digit code that you will
find in the code booklet – see method
B ).
Example: if you want to control a satellite receiver with the
DVD key, begin by entering a satellite code (any satellite,
for example: 603 for a Thomson satellite receiver) then
begin the procedure.
C B
This universal remote control is compatible with the majority of television sets, DVD
players, satellite receivers and infrared controlled cable.
This remote control has already been programmed so that you can use it to control
most of the audio/video products made by the THOMSON group. Before attempting to
programme the remote control, try it out by using one of the methods described in this
user manual.The two CR2032 batteries are already fitted in the remote control. Refer
to the diagram on the cover to replace them when they are worn out.
Please keep this guide along with the code list (provided separately), so that you can
programme your remote control for use with other products.
01-ROC3205_en 27/07/05 09:49 Page 1